manualshive.com logo in svg

Suzuki K9K, Service Manual, Page: 46 / 62

Share
Download
Suzuki K9K Service Manual Download Page 46

ENGINE MECHANICAL (K9K ENGINE) 6A2-47

a) Install bolt (3) and spacer (4) of special tool to crankshaft.
b) Install protector (2) together with new oil seal (1) to spacer 

(4).

c) Install oil seal installer (5) to bolt (3).

d) Tighten nut (6) of special tool until oil seal installer (5) 

comes into contact with gasket holder plate (7).

e) Remove special tools and protector (2).

5) Install timing belt referring to “Timing Belt and Belt Tensioner 

Removal and Installation” in this section.

6) Install engine assembly to vehicle referring to “Engine 

Assembly Removal and Installation” in this section.

Oil Pump and Oil Pump Chain Inspection

• Check rotor and oil pump cases for excessive wear or dam-

age.

 

If any malcondition is found, replace oil pump assembly.

• Check teeth of oil pump drive sprocket for wear or damage.

 

If any malcondition is found, replace oil pump drive sprocket.

• Check teeth of oil pump sprocket for wear or damage.

 

If any malcondition is found, replace oil pump assembly.

Summary of Contents for K9K































































Reviews:

No comments