30
30
6300158CE
6300158CE
Used
Used // interchangeable
interchangeable parts
parts and
and materials
materials
Material
Material code
code
KAILASH
KAILASH /
/ TRAVERSE
TRAVERSE /
/ VERTICAL
VERTICAL PRESSURE
PRESSURE SENSOR
SENSOR
100021395
100021395
LIGHT
LIGHT SHIELD
SHIELD PLASTIC
PLASTIC
100022977
100022977
WTC
WTC /
/ DIVING
DIVING PRESS.SENS.
PRESS.SENS. O-RING
O-RING
1000K4803
1000K4803
WTC/DIVING
WTC/DIVING PRESS.SENS.
PRESS.SENS. SUPPORT
SUPPORT BUSHING
BUSHING
100019722
100019722
Tools,
Tools, equipment,
equipment, security
security
Material
Material code
code
TORX
TORX SCREW
SCREW DRIVER
DRIVER 4X40
4X40
100013030
100013030
AMBIT PRESSURE SENSOR TOOL
AMBIT PRESSURE SENSOR TOOL
100019500
100019500
ESD
ESD TWEEZERS
TWEEZERS (SHARP
(SHARP CURVED
CURVED BLADE)
BLADE)
100019184
100019184
ESD
ESD TWEEZERS
TWEEZERS (wide
(wide blade)
blade)
100015252
100015252
Description
Description
1.
1. Remove the
Remove the lens, be
lens, bezel a
zel assembly, and
ssembly, and inner modu
inner module (in
le (instruction
struction 6300157CE
6300157CE
steps
steps
1-6)
1-6)
2.
2. Remove the
Remove the pressure
pressure sensor latch
sensor latch by open
by opening the
ing the screws with
screws with a Torx
a Torx 4
4 screwdriver.
screwdriver.
(Pic 1)
(Pic 1)
3.
3. Remove the
Remove the pressure sensor
pressure sensor by lifting
by lifting with tweezers
with tweezers from the
from the side, along
side, along the
the
ceramic pressure sensor plate. (Pic 2)
ceramic pressure sensor plate. (Pic 2)
4.
4. Remove the
Remove the pressure sensor
pressure sensor supports, and
supports, and sensor o-ring.
sensor o-ring. These may
These may be attached
be attached to
to
the old pressure sensor as well. If
the old pressure sensor as well. If the pressure sensor is to be re-used, be
the pressure sensor is to be re-used, be careful
careful
when removing them, use only plastic ESD tools
when removing them, use only plastic ESD tools if necessary to remove them.
if necessary to remove them.
5.
5. If the li
If the light shield
ght shield is the o
is the old metallic
ld metallic part, replace
part, replace it and
it and one of
one of the support
the support bushings
bushings
with the newer red lightshield.
with the newer red lightshield.
6.
6. Assemble the
Assemble the first pressure
first pressure sensor support
sensor support bushing and
bushing and a new
a new pressure sensor
pressure sensor o-
o-
ring on to the pressure sensor itself.
ring on to the pressure sensor itself. There should be 1 support, 1 o-ring and 1
There should be 1 support, 1 o-ring and 1
plastic lightshield. (Pic 3)
plastic lightshield. (Pic 3)
7.
7. Gently place
Gently place the new
the new pressure sensor
pressure sensor with the
with the assembled supports
assembled supports and o-ring
and o-ring into
into
the pressure sensor slot. The pressure sensor should sit
the pressure sensor slot. The pressure sensor should sit evenly in place before
evenly in place before
installing it fully. (Pic 4)
installing it fully. (Pic 4)
8.
8. Press the
Press the pressure
pressure sensor into
sensor into its socket
its socket using the
using the Ambit pressure
Ambit pressure sensor tool,
sensor tool,
carefully nudging with the tool until the sensor
carefully nudging with the tool until the sensor is in correct position. It
is in correct position. It should not slip
should not slip
out of place if installed correctly.
out of place if installed correctly. (Pic 5)
(Pic 5)
9.
9. Assemble the
Assemble the pressure sensor
pressure sensor latch and
latch and attach the
attach the latch with the
latch with the latch screws b
latch screws but
ut
be careful not to tighten them too
be careful not to tighten them too hard (See nominal values)
hard (See nominal values)
10.
10. Assemble the inner modu
Assemble the inner module, bezel assembly, perform a l
le, bezel assembly, perform a leakage test, and report the
eakage test, and report the
repair. (Instruction
repair. (Instruction 6300157CE
6300157CE
13-17)
13-17)
Nominal
Nominal and
and
limit
limit values
values
Vibra PCBA and Pressure sensor latch screws 7 ± 1 N
Vibra PCBA and Pressure sensor latch screws 7 ± 1 N cm
cm
1
1
The two Torx 4 Screws holding the Pressure
The two Torx 4 Screws holding the Pressure Sensor Latch.
Sensor Latch.
Pressure
Pressure
sensor
sensor
change
change
