Supero SUPER 370SSA User Manual Download Page 84

Page: 84 / 92

UPER 370SSA/370SSM

User's Manual

4-34

BIOS

Change Supervisor Password

This option allows you to change a supervisor password that was entered

previously.

Change User Password

This option allows you to change a user password that was entered previ-

ously.

Clear User Password

Use this option to clear the user password so that it is not required to be

entered when the system boots up.

Boot Sector Virus Protection

This option allows you to enable or disable a virus detection program to

protect the boot sector of your hard disk drive. The settings for this option

Disabled and Enabled. If Enabled, AMIBIOS will display a warning when

any program (or virus) issues a Disk Format command or attempts to write

to the boot sector of the hard disk drive.

Summary of Contents for SUPER 370SSA





























































































Search results

Summary of Contents for SUPER 370SSA

Reviews:

Related manuals for SUPER 370SSA

Brands by name

Popular brands

Supero SUPER 370SSA, User Manual

Search results

Summary of Contents for SUPER 370SSA

Reviews:

Related manuals for SUPER 370SSA

Brands by name

Popular brands