Supero SUPER 370SSA User Manual Download Page 82

Page: 82 / 92

UPER 370SSA/370SSM

User's Manual

4-32

BIOS

2nd Boot Device

The settings for the 2nd Boot Device are Removeable Device, Hard Drive,

ATAPI CDROM and LANDesk (R) Server.

3rd Boot Device

The settings for the 3rd Boot Device are Removeable Device, Hard Drive,

ATAPI CDROM and LANDesk (R) Server.

4th Boot Device

The settings for the 4th Boot Device are Removeable Device, Hard Drive,

ATAPI CDROM and LANDesk (R) Server.

Hard Disk Drives

Use this screen to view the hard drives that have been auto-detected or

entered manually on your system.

Removeable Devices

Use this screen to view the removeable devices that have been auto-de-

tected or entered manually on your system.

ATAPI CDROM Drives

Use this screen to view the ATAPI CDROM drives that have been auto-

detected or entered manually on your system.

Summary of Contents for SUPER 370SSA





























































































Search results

Summary of Contents for SUPER 370SSA

Reviews:

Related manuals for SUPER 370SSA

Brands by name

Popular brands

Supero SUPER 370SSA, User Manual

Search results

Summary of Contents for SUPER 370SSA

Reviews:

Related manuals for SUPER 370SSA

Brands by name

Popular brands