Supero SUPER 370SSA User Manual Download Page 74

Page: 74 / 92

UPER 370SSA/370SSM

User's Manual

4-24

BIOS

Legacy USB Support

This option allows Legacy USB support. The settings are Disabled, En-

abled and Auto. Disabled prevents the use of any USB device in DOS or

during system boot. Enabled allows the use of USB devices during boot

and while using DOS. The Auto setting auto detects USB keyboards or mice

and if found, allows them to be utilized during boot and while using DOS.

IRQ 3

IRQ 4

IRQ 5

IRQ 7

IRQ 9

IRQ 10

IRQ 11

IRQ 14

IRQ 15

The settings for the above options are Available and Reserved. Available

allows the specified IRQ to be available for use by PCI/PnP devices. Re-

served means the specified IRQ is reserved for use by Legacy ISA de-

vices.

DMA Channel 0

DMA Channel 1

DMA Channel 3

DMA Channel 5

DMA Channel 6

DMA Channel 7

Summary of Contents for SUPER 370SSA





























































































Search results

Summary of Contents for SUPER 370SSA

Reviews:

Related manuals for SUPER 370SSA

Brands by name

Popular brands

Supero SUPER 370SSA, User Manual

Search results

Summary of Contents for SUPER 370SSA

Reviews:

Related manuals for SUPER 370SSA

Brands by name

Popular brands