Supermicro X11DAC User Manual Download | Manualshive

Page: 139 / 216

background image

Appendix D: UEFI BIOS Recovery

139

Appendix D

UEFI BIOS Recovery

Warning:

Do not upgrade the BIOS unless your system has a BIOS-related issue. Flashing

the wrong BIOS can cause irreparable damage to the system. In no event shall Supermicro

be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS

update. If you need to update the BIOS, do not shut down or reset the system while the BIOS

is updating to avoid possible boot failure.

D.1 Overview

The Unified Extensible Firmware Interface (UEFI) provides a software-based interface
between the operating system and the platform firmware in the pre-boot environment. The
UEFI specification supports an architecture-independent mechanism that will allow the UEFI
OS loader stored in an external storage device to boot the system. The UEFI offers clean,
hands-off management to a computer during system boot.

D.2 Recovering the UEFI BIOS Image

A UEFI BIOS flash chip consists of a recovery BIOS block and a main BIOS block (a main

BIOS image). The recovery block contains critical BIOS codes, including memory detection

and recovery codes for the user to flash a healthy BIOS image if the original main BIOS image
is corrupted. When the system power is turned on, the recovery block codes execute first.

Once this process is complete, the main BIOS code will continue with system initialization
and the remaining POST (Power-On Self-Test) routines.

Note 1:

Follow the BIOS recovery instructions in Section D.3 for BIOS recovery when

the main BIOS block crashes.

Note 2:

If the recovery instructions in Section D.3 for BIOS recovery fail, you may use

the Supermicro Update Manager (SUM) Out-of-Band (OOB) (

https://www.supermicro.

com.tw/products/nfo/SMS_SUM.cfm

) to reflash the BIOS.

Note 3:

If the recovery block processes stated in Note 1 and Note 2 above fail, you will

need to follow the procedures to make a Returned Merchandise Authorization (RMA)
request. Refer to Section 3.5 for more information about the RMA request.

«
...
137
138
139
140
141
...
»

Summary of Contents for X11DAC

























































































































































































































Reviews:

No comments

Related manuals for X11DAC

Brand: MSI Pages: 48

Brand: JETWAY Pages: 52

Brand: Renesas Pages: 17

Brand: TOHATSU Pages: 52

Brand: Supermicro Pages: 111

Brand: MSI Pages: 45

Brand: Gigabyte Pages: 104

Brand: Daewoo Pages: 46

Brand: MSI Pages: 90

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 126

Brand: Fujitsu Pages: 30

Brand: Asus Pages: 2

EX-H310M-V3 R2.0

Brand: Asus Pages: 2

Brand: SOYO Pages: 119

Brand: Aaeon Pages: 30

Brand: Gan Systems Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands