manualshive.com logo in svg

Suntex PC-3110-RS, Operation Manual, Page: 20 / 68

Share
Download
Suntex PC-3110-RS Operation Manual Download Page 20

 

 
 

5. Operation                                                                                                                                             

5.1 Measurement mode 

     

After all electrical connections are finished and tested, connect the instrument to the power 

supply and turn it on. The transmitter will automatically entering measurement mode with the 
factory default settings or the last settings from user.   

5.2 Set-up menu 

     

Please refer to the set-up instructions in Chapter 7. Press      and       simultaneously to 

enter into set-up menu, and press       to

 

go press to back to measurement

 

mode. 

5.3 Calibration menu 

     

Please refer to the calibration instructions in Chapter 8. Press            and             

simultaneously to enter into calibration menu, and press       to go back to measurement

 

mode. 

5.4 Shortcuts: 

1. In the measurement mode, if selecting MTC for temperature compensation mode, you may press         

and     to adjust MTC temperature value. 

2. Under measurement mode, press     continuously for 2 seconds to see the Logbook function   
  directly. Press     key to back to measurement mode. 
3. Under measurement mode, press          continuously for 2 seconds to switch the display mode   
    from text mode, trace mode, and real-time chart display mode. 

5.5 Default value:   

5.4.1 Setting default value:

 

Measurement mode: pH 

 

Multi-Cal: 2 points pre-setting 

Temperature compensation: MTC 25°C 
Relay 1: High point alarm: AUTO, SP1= 10.00 pH, Hys= 0.10 pH 
Relay 2: Low point alarm: AUTO, SP2 =04.00 pH, Hys= 0.10 pH 
Wash time: OFF 
Analog 1 current output (pH/ORP): 4~20 mA, 0.00~14.00pH 
RS-485: RTU, Even, 19200, ID: 01   
Digital filter: 5 
Backlight setting: Off 
Code set-up: OFF 
Date & Time: 2012/1/1    00:00:00 
Contrast: 0 
Logbook: None 
Auto back: Auto, 3 minutes 

           

5.4.2 Calibration default value:

 

     

 

                                         

               

Asy: 0 mV 

Slope: -59.15 mV/pH @ 25.0˚C  

Calibration type: TECH-No Cal 
Calibration value: None data

 

Auto back: Auto, 3 minutes 

Note: The factory default of calibration presetting is “No Cal”, and the calibration value is “None”. It means that the 

user has not calibrated the sensor with the transmitter yet. After finishing every calibration, the display shows the 
calibration type and the calibration value. If the equipments have not been calibrated yet, the measurement takes 
pre-set Asy and Slope into calculation. The factory default values are subject to change without notice. 

16

Summary of Contents for PC-3110-RS





































































Reviews:

No comments