SunDash 20 GENESIS System 332 Pro-1 Operation & Assembly Instructions Download Page 30 | Manualshive

Page: 30 / 31

background image

Limited Acrylic Warranty

JK Products & Service warrants its acrylic sheets to be free from defects in material and
workmanship, under intended normal use, for a period of one (1) year from date of sale of the
tanning bed. Due to the tanning lotions, cosmetics, disinfectant and improper cleaners used on
tanning surfaces that cannot be controlled by JK Products & Service, after the first thirty (30) days
of warranty period. Acrylic will be subject to a prorated cost to the consumer on breakage.

JK Products & Service obligations do not include transportation charges on replacement acrylic.

JK Products & Service assumes no liability for the cost of removing defective sheets or installing
replacement sheets, nor for damage to persons or property.

To make a claim, contact an authorized dealer or distributor of JK Products & Services or JK
Products & Service, Service Department with the model number, the serial number, and the date
of purchase of the bed in which the acrylic will be used.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE
FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF FITNESS OR
MERCHANTABILITY.

THE REMEDIES PROVIDED IN THIS LIMITED WARRANTY ARE THE EXCLUSIVE
REMEDIES PROVIDED TO THE PURCHASER BY JK PRODUCTS & SERVICE AND ARE
PROVIDED IN SUBSTITUTION OF ALL OTHER REMEDIES - CONSEQUENTIAL AND
INCIDENTAL DAMAGES ARE EXCLUDED.

JK Products & Service

1 Walter Kratz Drive

Jonesboro, Arkansas 72401

1-800-445-0624

«
...
28
29
30
31
»

Summary of Contents for 20 GENESIS System 332 Pro-1
































Reviews:

No comments

Related manuals for 20 GENESIS System 332 Pro-1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands