SunDash 20 GENESIS System 332 Pro-1 Operation & Assembly Instructions Download Page 27 | Manualshive

Page: 27 / 31

background image

Setting Delay Time.

1) Press and hold the

START/STOP

and

UP

buttons at the same time until a

.1 appears on the display. This should take about 5 -6 seconds. Release the
buttons.
2) Press the

UP

button until a .3 is displayed.

3) Press and release the

START/STOP

button.

A number will appear on the display and be flashing. A period will be
illuminated in the center of the display. This is the current delay time.

4) Press the

UP

or

DOWN

Button until the desired delay time is displayed.

The highest delay time that can be set on the timer is 10 minutes. If you
want no delay time, set the display to 0. If you set the Delay Time to 0, the
session time will start immediately after the

START/STOP

button is

pressed.

5) Press the

START/STOP

button until a .3 is displayed. The 3 will not flash.

To exit Parameter Mode, press and hold the

UP

and

DOWN

buttons together

until the period disappears.

Starting a Session

1) Press the

UP

or

DOWN

button on the timer until the session time is

displayed. If the display shows a 0, and you want to count down from the
maximum time, press the

DOWN

button.

2) Press and release the

START/STOP

button to start the session.

If a delay other than 0 is entered, the delay will count down. A period on
the lower right corner of the display will flash rapidly. When the session
starts, the period will flash at a once per second rate.

Pausing a Session

To pause the session, press the

START/STOP

button; the flashing period on

the lower right corner of the display will stop flashing. The session time will
continue to count down. The tanning system will turn off.
To resume the session, press the

START/STOP

button on the timer. The

period on the lower right corner of the display will resume flashing.

Canceling a Session.

To cancel a session, press the

START/STOP

button to pause the session

then press the

UP

button. The display will show a solitary 0.

«
...
25
26
27
28
29
...
»

Summary of Contents for 20 GENESIS System 332 Pro-1
































Reviews:

No comments

Related manuals for 20 GENESIS System 332 Pro-1

Brand: KBL Pages: 60

Excellence 700 Turbo Power

Brand: ergoline Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands