Sun Microsystems Netra T5220 Service Manual Download Page 146

Page: 146 / 178

5-16

Sun Netra T5220 Server Service Manual • January 2012

FIGURE 5-14

Removing the Alarm Board Screws and Removing from Chassis

4. Set the alarm board aside on an antistatic mat.

5. Consider your next step:

■

If you removed the alarm board as part of another procedure, return to that
procedure.

■

Otherwise, continue to

Section 5.6.2, “Installing the Alarm Board” on page 5-16

5.6.2

Installing the Alarm Board

1. Remove the replacement alarm board from its packaging and place it on an

antistatic mat.

2. Seat the alarm board back into the chassis, and tighten the four alarm board

screws.

3. Reconnect the alarm board cables (

FIGURE 5-15

Summary of Contents for Netra T5220



















































































































































































Search results

Summary of Contents for Netra T5220

Reviews:

Related manuals for Netra T5220

Brands by name

Popular brands

Sun Microsystems Netra T5220, Service Manual

Search results

Summary of Contents for Netra T5220

Reviews:

Related manuals for Netra T5220

Brands by name

Popular brands