Sub-Zero ICBB-36R Design Manual Download Page 13

Page: 13 / 69

Built-In Refrigeration

subzero.com/specs

Flush Inset Application

It is necessary to consider the following points when
planning for a flush inset application:

•

The flush inset depth is 56 mm deeper than the
standard opening.

•

The flush inset width is 64 mm wider than the
standard opening.

•

The flush inset height is 6 mm higher than the
standard opening.

•

Panel widths increase to achieve the flush inset look.

•

You must allow a 13 mm reveal around the perimeter of
the unit and grille to allow for proper door swing and
airflow.

IMPORTANT NOTE:

The flush inset application is not a

separate model. This is an overlay unit in a flush installa-
tion. The same model is used in an overlay or flush inset
application.

Rough opening dimensions for the flush inset application
assume the use of a 19 mm decorative panel. The illustra-
tions at right show the difference between standard and
flush inset installations.

STANDARD INSTALLATION

610 mm

OPENING

DEPTH

TOP VIEW

Standard installation.

Flush inset installation.

665 mm

FLUSH

INSET

DEPTH

56 mm

32 mm

TOP VIEW

FLUSH INSET INSTALLATION

WITH

19 mm

PANEL

610 mm

OPENING

DEPTH

Summary of Contents for ICBB-36R






































































Search results

Summary of Contents for ICBB-36R

Reviews:

Related manuals for ICBB-36R

Brands by name

Popular brands

Sub-Zero ICBB-36R, Design Manual

Search results

Summary of Contents for ICBB-36R

Reviews:

Related manuals for ICBB-36R

Brands by name

Popular brands