Stryker Power-PRO XT, Maintenance Manual

Page: 11 / 186

W Wa arrn niin ng g//C Ca au uttiio on n//N No otte e D De effiin niittiio on n
The words W WA AR RN NIIN NG G, C CA AU UT TIIO ON N, and N NO OT TE E carry special meanings and should be carefully reviewed.
W WA AR RN NIIN NG G
Alerts the reader about a situation which, if not avoided, could result in death or serious injury. It may also describe
potential serious adverse reactions and safety hazards.
C CA AU UT TIIO ON N
Alerts the reader of a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to the
user or patient or damage to the product or other property. This includes special care necessary for the safe and effective
use of the device and the care necessary to avoid damage to a device that may occur as a result of use or misuse.
N No otte e -- Provides special information to make maintenance easier or important instructions clearer.
S Su um mm ma arryy o off ssa affe ettyy p prre ecca au uttiio on nss
Always read and strictly follow the warnings and cautions listed on this page. Service only by qualified personnel.
W WA AR RN NIIN NG G
• Always keep your hands clear of the red safety bar pivots when you load, unload, or change the height position of the
cot.
• Always use both hands when you transport the cot.
• P Po ow we err--P PR RO O with the P Po ow we err--L LO OA AD D compatibility option operates primarily at these frequencies: 70 - 85 kHz for
inductive charging and 13.56 MHz±7 kHz, Amplitude Modulated (OOK), ERP: -82.37 dBm. The inductive charging can
operate between these frequencies: 70 - 125 kHz. Other equipment may interfere with the P
Po ow we err--L LO OA AD D system, even
if that other equipment complies with CISPR emission requirements.
• Always relieve pressure before you disconnect hydraulic or other lines. Escaping fluid under pressure can penetrate the
skin and cause serious injury. Tighten all connections before you apply pressure. If an accident occurs, see a doctor
immediately.
• Do not use bare hands to check for hydraulic leaks.
C CA AU UT TIIO ON N
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in this
manual.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable operation
resulting in injury to patient or operator. Modifying the product also voids its warranty.
• This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at their expense.
• Always use authorized parts to avoid the risk of product damage.
• Always check hoses and lines regularly to avoid damage to the cot. Check and tighten loose connections. Hydraulic
lines, hoses, and connections can fail or loosen due to physical damage, kinks, age, and environment exposure.
• Do not tip the cot onto its load wheels and actuate the product as this will allow air to enter the hydraulic system.
• Do not lubricate the bearings in the X-frame as it will degrade the performance of the cot and may void its warranty.
• The cot retaining post is shipped pre-configured for an X-frame cot. If the fastener has been configured for an H-frame
cot, you must adjust the retaining post to accommodate the fastener.
• The use of accessories, transducers, and cables, other than those specified or provided by the manufacturer, could
result in increased electromagnetic emissions or decreased electromagnetic immunity and result in improper operation.
6506-109-002 Rev G.1 5 EN