Stryker Power-PRO XT Maintenance Manual Download Page 38

Page: 38 / 186

Fiig

urre

e 6

6 –– 1

2 V

C a

utto

ottiivve

e cca

blle

A ffu

ullllyy cch

arrg

d S

T P

akk d

ess n

ott p

prro

ovviid

e ssu

uffffiicciie

ntt p

err ffo

orr cco

ott o

erra

attiio

1. Fully charge the S

T Pak for two hours.

a. If the charger indicator LED is solid green, indicating a fully charged and ready S

T Pak, go to step 2.

b. If the charger indicator LED is solid amber, indicating a S

T Pak error, replace the S

T Pak.

2. Immediately following a full charge, remove the S

T Pak from the charger and check the voltage at the power

terminals on the Pak for 26 VDC minimum.

a. If the Pak has a 26 VDC minimum, go to step 3.

b. If the VDC is less than 26 VDC, replace the Pak.

3. Wait exactly one hour and charge the S

T Pak again.

a. If the charger indicator LED turns solid green (indicating a fully charged and ready S

T Pak) in less than one

minute, call Stryker Technical Support.

b. If the charger indicator LED flashes green for longer than one minute, replace the Pak.

T cch

arrg

err iin

diicca

atte

ess a

a S

T P

akk e

errrro

orr ((a

err L

D)),, b

utt tth

e P

akk p

errffo

orrm

mss

ellll o

n tth

e cco

ott

1. Fully discharge the S

T Pak by powering a cot until the cot indicator LED flashes red.

2. Recharge the Pak.

a. If the charger indicator LED is solid green, indicating a fully charged and ready Pak, then the Pak is ready for use.

b. If the charger indicator LED is solid amber, indicating a Pak error, call Stryker Technical Support.

arrg

err iin

diicca

atte

ess a

a tte

erra

attu

urre

e d

ella

ayy ((fflla

assh

hiin

g a

err L

D)),, b

utt tth

e P

akk iiss

wiitth

hiin

n tth

e n

orrm

all o

erra

attiin

g tte

erra

attu

urre

e rra

1. Remove the S

T Pak from the charger and allow the Pak to cool for at least four hours at room temperature.

2. Insert the Pak into the charger.

a. If the charger indicator LED is flashing green, then the Pak is charging.

b. If the charger indicator LED is flashing amber, indicating a temperature delay, replace the Pak.

6506-109-002 Rev G.1

Summary of Contents for Power-PRO XT



























































































































































































Search results

Summary of Contents for Power-PRO XT

Reviews:

Related manuals for Power-PRO XT

Brands by name

Popular brands

Stryker Power-PRO XT, Maintenance Manual

Search results

Summary of Contents for Power-PRO XT

Reviews:

Related manuals for Power-PRO XT

Brands by name

Popular brands