Stryker Power-PRO XT, Maintenance Manual

Page: 181 / 186

• Avoid stacking or placing other equipment adjacent to P Po ow we err--P PR RO O and S SM MR RT T charger to prevent improper operation of
the products. If such use is necessary, carefully observe P Po ow we err--P PR RO O and S SM MR RT T charger and the other equipment to
make sure that they are operating properly.
R Re ecco om mm me en nd de ed d sse ep pa arra attiio on nss d diisstta an ncce ess b be ettw we ee en n p po orrtta ab blle e a an nd d m mo ob biille e R RF F cco om mm mu un niicca attiio on nss e eq qu uiip pm me en ntt a an nd d P Po ow we err--
P PR RO O a an nd d S SM MR RT T cch ha arrg ge err
P Po ow we err--P PR RO O and S SM MR RT T charger are intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of P Po ow we err--P PR RO O and S SM MR RT T charger can help prevent
electromagnetic interferences by maintaining a minimum distance between portable and mobile RF communications
equipment (transmitters) and P
Po ow we err--P PR RO O and S SM MR RT T charger as recommended below, according to the maximum
output power of the communications equipment.
R Ra atte ed d m ma axxiim mu um m o ou uttp pu utt
p po ow we err o off ttrra an nssm miitttte err
W
S Se ep pa arra attiio on n d diisstta an ncce e a acccco orrd diin ng g tto o ffrre eq qu ue en nccyy o off ttrra an nssm miitttte err
m
1 15 50 0 kkH Hzz tto o 8 80 0 M MH Hzz
D D= =((1 1..2 2)) ((√ √ P P ))
8 80 0 M MH Hzz tto o 8 80 00 0 M MH Hzz
D D= =((0 0..3 35 5)) ((√ √ P P ))
8 80 00 0 M MH Hzz tto o 2 2..7 7 G GH Hzz
D D= =((0 0..7 70 0)) ((√ √ P P ))
0.01 0.12 0.04 0.07
0.1 0.38 0.11 0.22
1 1.20 0.35 0.70
10 3.79 1.11 2.21
100 12 3.50 7
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters
(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output
power rating of the transmitter in watts (W) according to the transmitter manufacturer. Note 1: At 80 MHz and 800 MHz,
the separation distance for the higher frequency range applies. Note 2: These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people.
G Gu uiid da an ncce e a an nd d m ma an nu uffa accttu urre err’’ss d de ecclla arra attiio on n -- e elle eccttrro om ma ag gn ne ettiicc iim mm mu un niittyy
P Po ow we err--P PR RO O and S SM MR RT T charger are suitable for use in the electromagnetic environment specified below. The customer
or the user of P Po ow we err--P PR RO O and S SM MR RT T charger should assure that they are used in such an environment.
IIm mm mu un niittyy tte esstt
IIE EC C 6 60 06 60 01 1 tte esstt lle evve ell
C Co om mp plliia an ncce e lle evve ell
E Elle eccttrro om ma ag gn ne ettiicc
e en nvviirro on nm me en ntt--g gu uiid da an ncce e
Electrostatic discharge
(ESD)
IEC 61000-4-2
+8 kV contact
+15 kV air
+8 kV contact
+15 kV air
Floors should be wood,
concrete or ceramic tile. If
floors are covered with
synthetic material, the
relative humidity should be
at least 30%.
Electrostatic fast Transient/
burst
IEC 61000-4-4
+2 kV for power supply lines
+1 kV for input/output lines
P Po ow we err--P PR RO O: N/A
S SM MR RT T charger (6500-201-
010): +2kV for power supply
lines
+1 kV for input/output lines
Mains power quality should
be that of a typical
commercial or hospital
environment.
6506-109-002 Rev G.1 175 EN