Stryker LIFEPAK 20 Inspection Procedure Download Page 48

Page: 48 / 61

LIFEPAK

Performance Inspection Procedure (PIP)

3201896-000_B

--- CONTENTS ---

Page 48 of 61

PIP - Leakage Current Tests

Perform leakage current testing in accordance to the following electrical safety standards:

IEC (International Electro technical Commission) 62353.

WARNING

SHOCK HAZARD

Failure to properly perform these tests could result in a failure to detect excessive leakage current. Make sure you are familiar
with your test equipment and these test performance procedures.

Leakage

– Current flow induced by the application of high voltage to a material or object with high dielectric strength.

Normal Condition (N.C.)

– AC voltage is applied in either normal or reversed polarity (that is, measurements made with the POLARITY

switch in both NORMAL [NC] and REVERSED [RM] positions). The earth ground is intact during these measurements.

Single Fault Condition (S.F.C.)

– AC voltage is applied in either normal or reversed polarity (that is, measurements made with the

POLARITY switch in both NORMAL [NC] and REVERSED [RM] positions). The earth ground is NOT intact during these
measurements.

Safety Analyzer setup instructions are specific to the Fluke Biomedical ESA612.

Summary of Contents for LIFEPAK 20






























































Search results

Summary of Contents for LIFEPAK 20

Reviews:

Related manuals for LIFEPAK 20

Brands by name

Popular brands

Stryker LIFEPAK 20, Inspection Procedure

Search results

Summary of Contents for LIFEPAK 20

Reviews:

Related manuals for LIFEPAK 20

Brands by name

Popular brands