Stiga SRC 750 G Operating Instructions Manual Download

Page: 17 / 172

9 - WARNING !! The petrol/gasoline is highly inflammable: Don’t fill the tank neither in closed areas, nor when engine is on, don’t smoke and

be careful to the petrol/gasoline loss from the tank. In case of leak, don’t try to switch the engine on but move the machine away from the area

in order to avoid ignition source until the gasoline vapours fade away. Re-place the tank caps and the gasoline box.

10 - Keep attention to the exhaust pipe. The parts near the pipe can reach 80°C.

Replace the defective and/or worn out silencers Burn hazards !!!.

11- Don’t use the motor hoe on steep slopes: it could overturn!. On slope it is recommended to work crosswise, neither in slope nor in descent

and be vary careful during any change of direction.

12 - Before putting the machine into operations, check it visually and make sure all the accident prevention measures are working. It is

absolutely forbidden to exclude and/or to tamper with them. Replace worn or damaged elements.

13 - In case the machine is incorrectly used, and/or the repairs are performed by non-authorized technical staff, and/or fitted by spare parts

other then original ones: any use other than that described above is prohibited and will involve the cancellation of the warranty and the refuse

all responsibility from the manufacturer.

SAFETY FEATURE (Fig. 14)

All motor-hoes are provided with a safety feature which acts. The device causes the transmission to disconnect

automatically anytime the respective control levers are released (2 Forward speed – 3 Reverse speed).

NOTES ON HOW TO WORK WITH THE MOTOR-HOE

With the engine running, rest the tines on the ground, and firmly holding the

motor-hoe, insert the spur into the soil. Lower the clutch lever on the handlebar to allow the disks to bite into the soil. The motor-hoe will move forwards

when the handlebars are used to slightly lift the disks. The spur arm must always remain in the soil during work. Uses: Light or medium textured soil

working. Soil working (hoeing/breaking-up). Soil tillage (weeding). Ploughing in compost or fertilizers, etc. Attention: The motor-hoe is unsuitable for

working in soils covered by thick grass/lawns. It is also unadvisable to use the implement on stony soils.

TRANSPORT

A forklift truck should be used to move the machine. The forks should be opened as far as possible and inserted into the pallet. The

weight of the machine is given on the Manufacturer’s data plate together with the other technical information. Motor-hoe can be transported to given

place by means of transport wheel (Fig 14 part. 8). Switch off the engine before transporting the machine.

HOW TO ASSEMBLE YOUR MOTOR-HOE

Unless otherwise agreed, the motor-hoe is delivered disassembled and placed in a packing

case. For assembly to be completed, the step by step procedure is as follows :

TRANSFER WHEEL (Fig. 2 A and 2 B)

Take from the packing box the support wheel complete with wheel (1) and insert it in the front seat of the frame

(A). Fit the spring (2) and secure it with the washer (3) and the cotter pin (4) into the housing hole. The wheel support is in the transport position as

shown in Fig. 2A. To shift to work position pull it towards the wheel support (1) and turn it to the right until it stops. See fig. 2 B. The spring, washer and

cotter pin can be found inside the bag accessories.

SPUR (Fig. 3)

Insert the spur (1) in correspondence of the hole of the frame (A). Secure with washer (2) and with the R pin (3) you can find in the

accessories bag.

HANDLEBAR ASSEMBLY ( Fig. 4) :

To assemble the handlebar (1) on the tiller frame, perform the following steps:

In the upper hole to pass the screw (2) in the grommet (3) with already entered the control cables and then secure it with the nut (4). Use the lower slot