STIEBEL ELTRON WPL 15 IKS-2 Operation And Installation Download Page 60

Page: 60 / 76

INSTaLLaTION

maintenance

| WPL 15 IKS | WPL 25 IK

www.stiebel-eltron.com

16. Maintenance

WARNING Electrocution

Before working on the appliance, isolate it from the

power supply at the control panel.

Following isolation from the mains supply, parts of the

appliance may remain live for up to 2 minutes since the

capacitors still have to discharge into the inverter.

DANGER Risk of electrocution!

Prior to maintenance work, isolate the internal and

external units from the power supply.

Note

Ensure that the refrigerant circuit is tested once a year for

leaks, in accordance with EC DIRECTIVE 517/2014.

The tightness test must be documented in the log.

Before any work on the appliance, disconnect all poles of any

in-built electric components from the power supply.

Regularly vent the safety valve until a full stream of water

flows from it. Close the safety valve following inspection.

Please note that the heating system is only free of dirt if the strai-

ners are completely clean following a prolonged pump runtime.

Material damage

Escaping refrigerant is damaging to the environment.

Any leaks in the refrigerant circuit must be remedied

immediately. Work on the refrigerant circuit must only

be carried out by qualified contractors.

We recommend a regular inspection (to establish the current con-

dition of the system), and maintenance if required (to return the

system to its original condition).

16.1 DHW cylinders

Opening the appliance

�0

3�

�1

Undo the screws and open the appliance door.

�0

3�

�1

753

Undo the screws and remove them.

Remove the lower appliance door.

Draining the DHW cylinder

WARNING Burns

Hot water may escape when draining the DHW cylinder.

Close the shut-off valve in the cold water line.

Open the hot water taps on all draw-off points.

�0

3�

�1

1 Drain

Empty the DHW cylinder via the drain.

Please note that some residual water will remain in the bottom

of the cylinder.

Cleaning and descaling

Remove the flange plate.

Clean the DHW cylinder through the inspection port.

Never use descaling pumps. Never use descaling agents for

the purpose of cleaning the enamel coating and protective

anode.

Summary of Contents for WPL 15 IKS-2













































































Search results

Summary of Contents for WPL 15 IKS-2

Reviews:

Related manuals for WPL 15 IKS-2

Brands by name

Popular brands

STIEBEL ELTRON WPL 15 IKS-2, Operation And Installation

Search results

Summary of Contents for WPL 15 IKS-2

Reviews:

Related manuals for WPL 15 IKS-2

Brands by name

Popular brands