STIEBEL ELTRON WPL 15 IKS-2 Operation And Installation Download Page 26

Page: 26 / 76

INSTaLLaTION

appliance installation

| WPL 15 IKS | WPL 25 IK

www.stiebel-eltron.com

10.2.2 Siting

Observe chapter “Preparations / External unit / Sound

emissions”.

A condensate drain is fitted to the defrost pan at the factory, to

enable the condensate to drain off.

Example: Foundation slab

WPL 15 IKS-2

600

1200

150

160

00000

2846

WPL 25 IK-2

620

1370

160

00000

2846

1 Air intake

2 Air discharge

3 Main wind direction

4 Condensate drain outlet

5 Refrigerant suction gas line

6 Refrigerant, liquid line

00000

2846

A Depth of frost line

1 Refrigerant suction gas line

2 Refrigerant, liquid line

3 Condensate drain

4 Drainage pipe

5 Foundation

6 Gravel bed

00000

Secure the appliance to the base using the 4 fixing brackets

(see internal unit standard delivery) and the associated

screws and rawl plugs.

Summary of Contents for WPL 15 IKS-2













































































Search results

Summary of Contents for WPL 15 IKS-2

Reviews:

Related manuals for WPL 15 IKS-2

Brands by name

Popular brands

STIEBEL ELTRON WPL 15 IKS-2, Operation And Installation

Search results

Summary of Contents for WPL 15 IKS-2

Reviews:

Related manuals for WPL 15 IKS-2

Brands by name

Popular brands