STIEBEL ELTRON WPL 15 IKS-2 Operation And Installation Download Page 13

Page: 13 / 76

OPEraTION

Settings

www.stiebel-eltron.com

WPL 15 IKS | WPL 25 IK |

TEmPEraTUrES

meaning

OUTSIDE

Outside temperature

ACT ROOM T FE7

Actual room temperature for heating circuit 1 (HC1) or heating circuit 2 (HC2)

(will only be displayed if the FE 7 remote control is connected)

SET ROOM T FE7

Set room temperature for heating circuit 1 or heating circuit 2

(will only be displayed if the FE 7 remote control is connected)

REL HUMIDITY

Relative humidity (will only be displayed if the FEK remote control is connected)

DEW POINT TEMP

Dew point temperature (will only be displayed if the FEK remote control is connected)

ACTUAL DHW T

Actual DHW temperature

SET DHW TEMP

Set DHW temperature

ACTUAL RTRN T

Actual heat pump return temperature for heating circuit 1

ACT HP FLOW T

Actual heat pump flow temperature

ACT NGT FLOW T

Flow temperature of electric emergency/booster heater

HTG CIRC ACT T

Actual heating circuit temperature for heating circuit 1

HTG CIRC SET T

Set heating circuit temperature for heating circuit 1 (HC1). Fixed temperature is displayed with set value control.

ACTUAL MIXER T

Actual mixer flow temperature for heating circuit 2

SET MIXER TEMP

Set mixer flow temperature for heating circuit 2

ACT BUFFER T

Actual buffer temperature

FIXED FLOW T

Set fixed temperature for heating circuit 1

SET BUFFER T

Set buffer temperature (Highest set value of heating circuits H1 and H2. Fixed temperature will be displayed for fixed temperature

control.)

DUAL-MODE HTG

Dual-mode point - central heating

DUAL-MODE DHW

Dual-mode point - DHW

SYST FROST PRO

System frost protection temperature

HEATING PRES

ACT VOLUME

Current flow rate [l/min]

MAX VOLUME

Flow rate for monitoring the defrost process [l/min]

STATUS HP 1

Status signal for "HP operation" and "HP fault"

STATUS HP 2

Status signal for "HP compressor�ON" and "defrost mode"

ST HP OPERATN

Heat pump operation ON/OFF

ST HP COMP

Compressor ON/OFF

ST HP FAULT

Refrigerant circuit fault ON/OFF (ON= fault, OFF = no fault)

ST HP DEFROST

Defrost mode ON/OFF

OUTPUT HP

Controller output signal for heat pump output control

INT PUMP RATE

Circulation pump output

HEAT AMOU DAY

Amount of compressor heat generated in heating mode since 0:00 h today.

TTL HEAT AMOU

Total amount of compressor heat generated in heating mode.

HEAT AMOU DAY

Amount of compressor heat generated in DHW mode since 0:00 h today.

TTL HEAT AMOU

Total amount of compressor heat generated in DHW mode.

TTL HEAT AMOU

Total amount of heat generated by the electric booster heater in heating mode.

TTL HEAT AMOU

Total amount of heat generated by electric reheating in DHW mode.

Summary of Contents for WPL 15 IKS-2













































































Search results

Summary of Contents for WPL 15 IKS-2

Reviews:

Related manuals for WPL 15 IKS-2

Brands by name

Popular brands

STIEBEL ELTRON WPL 15 IKS-2, Operation And Installation

Search results

Summary of Contents for WPL 15 IKS-2

Reviews:

Related manuals for WPL 15 IKS-2

Brands by name

Popular brands