background image

Propane Vapor

Withdrawal

or

Natural Gas

Congratulations!

You have purchased the finest circulating  heater available. 

Your new L.B. White heater incorporates the benefits from the most experienced
manufacturer of heating products using state-of-the-art technology.

We, at L.B. White, 

thank you

for your confidence in our products and welcome 

any suggestions or comments you may have...contact us at 1-800-345-7200, or
email us at [email protected].

Owner's Manual and Instructions

Premier Ductable Heaters

View this manual online at www.lbwhite.com

MODELS

INPUT 

(Btuh/kW)

FUEL

TS080

80,000/23.4

TS170

170,000/49.8 

Certification by:

150-30033 REV.A

ATTENTION ALL USERS

This heater has been tested and evaluated by C.S.A. International in accordance
with the requirements of Standard ANSI Z83.7

l

CSA 2.14 and is listed and approved

as a ductable direct gas-fired forced-air construction heater with application for the
temporary heating of buildings under construction, alteration, or repair.  Additionally,
this heater has been application reviewed and approved by C.S.A. International for
U.S.and Canadian Tent Heating Applications with temporary human occupancy.  If
you are considering using this product for any application other than its intended
use, then please contact your fuel gas supplier, or the L.B. White Co., Inc.

SCAN THIS QR CODE

with your smartphone or 
visit http://goo.gl/5j21G to
view maintenance videos
for L.B.White heaters.*

*Requires an app like QR Droid for Android or 
QR Reader for iPhone.

Summary of Contents for Premier TS080



































Reviews: