background image

1. Open the burner end access doorand remove gas

hose from heater.

2. Remove the elbow and all screws at inlet of gas

control valve.  See Fig. 21.

FIG. 21

3. Remove the burner retaining bolt at the underside of

the heaters base.  For Premier 170 heaters, the bolt

is accessible through an opening in the heater’s

support leg.  Use a ratchet with extension and 9/16

in. socket.  See Fig. 22.  For model TS080, also

remove the spacer between heater base and burner.

See Fig. 23.

FIG. 22

FIG. 23

This heater has two limit switches, one on the heat

chamber, the other on the fan housing.  Both switches

should be tested annually, typically when the heater is given

a thorough cleaning.

1. Remove either high limit switch.

2. Holding the switch by one of its mounting legs, apply

a small flame only to the sensing portion on the back

of the switch.  Be careful not to melt the plastic

housing of the switch when conducting this test.

3. Within a minute, you should hear a pop coming from

the switch, indicating the contacts of the switch have

opened.

4. Allow the switch cool down for about a minute.

Remove the red cap and firmly press the reset button

on the switch.

5. Check for electrical continuity across the switch

terminals to make sure the contacts have closed.

Install red cap.

FIG. 20

TESTING THE MANUAL RESET HIGH LIMIT SWITCHES

WARNING

Fire Hazard

Do not operate the heater with the high limit switch

bypassed.  

Operating the heater bypassed high limit switch may

lead to overheating, possibly resulting in a fire, with

subsequent damage to the heater or property damage.

BURNER ORIFICE & GAS CONTROL VALVE

SPACER

BOLT

18

Summary of Contents for Premier TS080



































Reviews: