STIEBEL ELTRON SOM 8 PLUS Installation Manual Download Page 5

Page: 5 / 84

Installation

2.1

Mounting

the unit must only be located in dry interior rooms.
the controller must additionally be supplied from a

double pole switch with contact gap of at least 3 mm

[0.12"].
please pay attention to separate routing of sensor

cables and mains cables.
In order to mount the device to the wall, carry out

the following steps:

unscrew the cross-head screw from the cover

and remove it along with the cover from the

housing

mark the upper fastening point on the wall. Drill

and fasten the enclosed wall plug and screw lea-

ving the head protruding

Hang the housing from the upper fastening

point and mark the lower fastening points (cen-

tres 223 mm [8.8"])

Insert lower wall plugs

Fasten the housing to the wall with the lower

fastening screws and tighten

Carry out the electrical wiring in accordance

with the terminal allocation, see chap. 2.2

put the cover on the housing

attach with the fastening screw

1.1

Optional functions

Solar

Bypass
Cs Bypass
external heat exchanger
tube collector
target temperature
antifreeze
afterheating suppression
parallel relay
Cooling mode
Drainback
twin pump
Heat dump
Flow rate monitoring

Arrangement

parallel relay
mixer
Boiler loading
error relay
Heat exchange
solid fuel boiler
Circulation
return preheating
Function block
Irradiation switch

Heating

thermal Disinfection
DHW heating

WARNING!

Electric shock!

upon opening the housing, live

parts are exposed.

Always disconnect the

controller from power supply

before opening the housing!

cover

screw

Note

strong electromagnetic fields can impair

the function of the controller.
make sure the controller as well as the sys-

tem are not exposed to strong electroma-

gnetic fields.

upper fastening point

lower fastening point

295931-36390-8667 SOM 8 plus_en.indb 5

20.10.2011 13:14:20

Summary of Contents for SOM 8 PLUS





















































































Search results

Summary of Contents for SOM 8 PLUS

Reviews:

STIEBEL ELTRON SOM 8 PLUS, Installation Manual, Page: 5 / 84

Search results

Summary of Contents for SOM 8 PLUS

Reviews: