SteelMax Rail Runner LT Operator'S Manual Download | Manualshive

Page: 38 / 53

background image

Rail Runner LT

Rail Runner LT

– Operator’s Manual

38

5.16. Torch holders

5.16.1. Short rod torch holder with clamp

Allows using a torch with the diameter of 16

–22 mm (0.63–0.87″).

5.16.2. Short rod torch holder with clip

The holder allows using a torch with the diameter of 16

–22 mm (0.63–0.87″). Use the

4 mm hex wrench to tighten the torch in the clip.

5.16.3. Short rod low torch holder with clip

The holder allows using a torch with the diameter of 16

–22 mm (0.63–0.87″). Use the

4 mm hex wrench to tighten the torch in the clip.

Part number:
UCW-0476-20-00-00-0

Part number:
UCW-0476-27-00-00-0

Part number:
UCW-0476-06-00-00-0

«
...
36
37
38
39
40
...
»

Summary of Contents for Rail Runner LT






















































Reviews:

No comments

Related manuals for Rail Runner LT

Brand: Abicor Binzel Pages: 92

Brand: p-light Pages: 28

Brand: Keithley Pages: 79

Brand: Kayakpro Pages: 17

Brand: Yoshitake Pages: 11

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brand: Raymarine Pages: 15

Brand: RaycoWylie Pages: 9

Brand: Raven Pages: 58

Brand: Raven Pages: 26

Brand: Ravo Pages: 114

Brand: Alcoscan Pages: 6

Brand: RAMVAC Pages: 53

So-exercise TX7

Brand: T-SoX Pages: 8

Brand: Bayer HealthCare Pages: 104

EDC2-1001-RGB-MWT

Brand: Energizer Pages: 18

Brand: MIETHKE Pages: 125

Brand: Stamina Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands