SteelMax Rail Runner LT Operator'S Manual Download | Manualshive

Page: 27 / 53

background image

Rail Runner LT

Rail Runner LT

– Operator’s Manual

27

5.8.2. Pivoting magnetic unit

Allows clamping a semi-flexible or rigid track to ferromagnetic surfaces that are

concave or convex, to pipes with outer diameters of at least 800 mm (31.5

″), and to

surfaces that differ in height up to 80 mm (3.1

″). The holding force on a 5 mm (0.2″)

thick surface is 1200 N up to a temperature of 100°C (212°F). At 180°C (356°F) the

force decreases to 720 N.

Install the unit in the same way as the magnetic unit is installed. To adjust the

angle, use the 6 mm hex wrench and loosen four side screws.

Part number:
ZSP-0475-85-00-00-0

Part number

(bracket for semi-flexible track):

DYS-0482-19-00-00-0

Part number

(bracket for rigid track):

DYS-0482-21-00-00-0

«
...
25
26
27
28
29
...
»

Summary of Contents for Rail Runner LT






















































Reviews:

No comments

Related manuals for Rail Runner LT

Brand: NARGESA Pages: 33

Brand: DARAY Pages: 28

Brand: MacDon Pages: 88

Brand: Jiffy Pages: 15

Brand: idiag Pages: 10

Brand: Bandit Pages: 136

Versaflo S Series

Brand: 3M Pages: 11

DBI Sala EXOFIT

Brand: 3M Pages: 32

Brand: 3M Pages: 8

Brand: Accurate Bio-Medical Technology Pages: 35

Brand: RASHA PROFESSIONAL Pages: 11

Brand: MADRIX Pages: 24

Brand: MADRIX Pages: 28

Crouse-hinds series

Brand: Eaton Pages: 32

COOPER POWER SERIES

Brand: Eaton Pages: 8

Brand: Saadat Pages: 61

Brand: Saadat Pages: 22

TR 2B INC INT NC

Brand: OMGA Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands