20
21
F11 Restore factory setting:
This option allows the system to restore the factory
setting rapidly.
F12 Valet/Personal mode setting for programming
There are two modes of F12: Valet mode and Personal
code mode.
When F12 is in Valet mode, you can program the
functions/features of F12~25 through Valet switch.
When F12 is in Personal code mode, you can program
the functions/features of F12~25 by input personal
code.
F13 Transponder card
The transponder card is an additional upgrade
accessory.
F13/1 Turn off the transponder card detection.
F13/2 Turn on the transponder card detection. If the
transponder card is not found, the engine will be
immobilized.
F13/3 Turn on the transponder card detection and
anti-hijack will be activated automatically when the
transponder card is not detected.
F14 Ignition warning in disarmed mode
In disarmed mode, when ignition is on, the ignition
icon (
) will show on the LCD transmitter.
F15 INST2 (-) extra input trigger
Select between an INST2 extra input (-) or a
speedometer input (-).
F16 Anti-hijack by transmitter
To activate the anti-hijack by pressing transmitter
button and
together when ignition is on.
F17 Anti-hijack by ignition on
To activate the anti-hijack by ignition on or by a
door opening (-) while the ignition is on.
F18 Anti-hijack by ignition on
To activate the anti-hijack by a door opening (+)
while the ignition is on or by the speedometer trigger.
F19 Arm (-)
F19/1: The output (-) of Black/White wire is reverse
to the armed output (-) (Orange wire). That means,
when the Orange wire outputs signal (-), the
Black/White wire will not output signal (-), when the
Orange wire does not output signal (-), the
Black/White wire will output signal (-).
F19/2: Black/White wire will output signal (-) for
turbo timer.
F20 CH5 output
F20/1: The output (-) of Gray wire is reverse to the
armed output (-) (Orange wire).
F20/2: The Gray wire will output a signal (-) to trigger
a pager when the alarm system is triggered.
F21 CH6 output: two blue/black wires
Select between turbo timer and W-mode.
F21/1: output signal (-) for 20 seconds after
disarmed. This option is recommended to trigger
the headlight output.
Installation instruction
Before you begin the installation
*
Read the INSTRUCTIONS!
*
Always use a multi-meter when verifying vehicle
wiring.
*
Before mounting the product, verify with the
customer's desired location for the valet switch and
LED.
*
Always look before drilling. Make sure you will not
cause damage to vehicle hoses, electrical looms or
physical damage to vehicle.
Mounting ECU
Mount the ECU under the dash where it will be
difficult for a potential thief to locate the module,
and away from moving parts such as brake pedals,
etc.
Antenna module
For optimum range and performance, the antenna
module should be located high up on the front
windshield glass. For example: behind the rearview
mirror.
Note: Window tints or Films may decrease the range
of the system. The mounting surface for the antenna
should be clean and dry.
Mounting siren
Mount the siren in a suitable place under the hood,
away from hot and moving engine parts. Make sure
the siren cannot be accessed from underneath the
F21/2: output signal (-) for turbo timer according to
the time of the F1 setting.
F21/3/4/5: The channel will activate according to
the W-mode setting. Select among
1
start and stop by real time (according to the W-
mode setting to start and stop);
2
start for 1 second by real time (according to the
w-mode setting to start for 1 second signal);
3
start for 1/0.5/1 sec by real time (according to
the w-mode setting start for 1 second and pause
for 0.5 second then a 1 second signal)
F22 Window/sunroof closer
This option suits for vehicle with automatic
window/sunroof close function. Select for 10
seconds, 15 seconds, 22 seconds or 30 seconds
to close the window/sunroof.
F23 Passive arming
The system will arm automatically 30 seconds after
the car is parked and all doors are closed.
F24 Door lock if passive arming on
All doors will lock while passive arming.
F25 STOP (-/+) function of door trigger
F25/1: no change to the door trigger
F25/2: door trigger (+) wire (violet) will be defined
not for door trigger, e.g. it can be defined as a
footbrake trigger (+).
F25/3: door trigger (-) wire (brown) will be defined
not for door trigger, e.g. it can be defined as a
footbrake trigger (-).
Summary of Contents for 888W1
Page 1: ......
