19. Turbo timer mode (F1, F19, F21)
The time can be programmed (F1). Turbo timer
works after the engine runs for more than 60 seconds.
If the turbo timer mode is on, when you take out the
key, the engine will keep running, the parking lights
will flash once every 2 seconds. The remaining time
will be shown on LCD transmitter.
Turbo timer mode keeps the engine running after
arriving at you destination for a programmable period
of 1, 3, 10, 15 or 30 minutes (F1). This allows the
system to cool down the turbo after you have left
the vehicle.
To activate turbo timer mode, "turbo timer output"
(F19/2 or F21/2) needs to be set.
*
Turn off the key, the engine will keep running.
*
The LCD transmitter will beep 3 times and the
display will show:
*
The parking lights will flash once every 2 seconds
to indicate the turbo timer mode is on.
*
The engine will turn off after the programmed time
runs out.
To cancel turbo timer mode:
a) Take the key out
b) Press button
twice
c) Siren will chirp twice and the parking lights will
flash once.
20. Transmitter operation range indication
In armed mode, the signal icon on the operated LCD
transmitter shows that the transmitter is within the
operation range of the system. The signal icon will
disappear in 2 minutes when the LCD transmitter is
out of the operation range and cannot receive the
signal from the system. At the same time, 2 beeps
will be heard when any LCD transmitter button is
pressed.
When a transmitter sends signal to the system, the
system only send feedback signal to the transmitter.
21. Rearming automatically
When the system is disarmed by pressing button
and the doors are not opened in 20 seconds (plus
F6 arming delay time), the system will rearm with the
doors locked automatically (door lock or unlock is
determined by F5). The siren will beep once with
parking lights flash.
22. Ultrasonic sensor (optional)
When the ultrasonic sensor is triggered by detecting
an object movement inside the vehicle, the siren will
alarm for 30 seconds with parking lights flashing. The
engine will be immobilized.
23. Tamper alert
If the alarm was triggered while you are away from
the vehicle, the siren will chirp 4 times with the parking
lights flash on disarming for tamper indication. The
LED will flash the zone that was triggered.
24. Personal code setting
Personal code can be programmed (F12). The factory
setting personal code is 11.
24.1. How to enter the personal code:
Disarm system, turn ignition off and wait for 5
seconds, then turn ignition ON/OFF/ON.
Press and release the valet switch the number of
times according to the first digit of personal code
in 10 seconds. (eg. The first digit of factory setting
personal code is 1, press and release the valet
switch once).
Turn ignition OFF/ON.
Press and release the valet switch the number of
times according to the second digit of personal code
in 10 seconds.
Turn ignition OFF/ON.
When the input personal code is correct, the system
will send out a "short" chirp and a "long" chirp.
24.2. How to change the personal code:
After the correct personal code is entered, turn
ignition off in 5 seconds.
Press valet switch 5 times, the siren will send out
one short and one long chirp to confirm entering the
setting mode.
Press transmitter button once in 5 seconds (the
siren will chirp once).
Press valet switch the number of times according
to the first digit of the personal code (from 1 to 9)
in 10 seconds, the siren will chirp accordingly.
Press transmitter button
once in 10 seconds (the
siren will chirp once).
Press valet switch the number of times according
to second digit of personal code (from 1 to 9) in
10 seconds, the siren will chirp accordingly. Turn
ignition on, the siren will send out one short and one
long chirp to confirm the new personal code is set
successfully.
If the changing is not successful, please disarm the
system and repeat the procedure mentioned above.
25. Transmitter and transponder (optional) code
learning
To learn new transmitters, the learning procedures
will be different depending on the settings of F12:
F12 - valet
Switch off the power of the transponder card (if
available)
Disarm system, turn ignition on.
Press valet switch 3 times, the siren will chirp once.
Press and hold button on the first transmitter till
one chirp is heard, and then LED will start to flash
slowly.
Press and hold button on the second transmitter
till one chirp is heard, and then LED will start to flash
slowly.
Only 2 transmitters can be programmed for the
system.
Switch on the power of transponder card, the
transponder card will be programmed successfully
with one chirp.
Turn ignition off to exit or 10 seconds later to exit
automatically.
12
13
Summary of Contents for 888W1
Page 1: ......
