stayer SN1435B, Operating Instructions Manual

Page: 22 / 44

ENGLISH
22
22
Cutting Angle Adjustment
To cut from 0° to 45°, loosen knob 22 (model SN1735 has
additional knob 20) and turn saw frame body 5 to the left
until selecting the angle desired from the scale indicated.
Once selected set the frame by tightening knob 22 .
Cutting Angle Calibration
You can verify and, if necessary, adjust 0° to 45° for
cutting by using a set square between 90°and 45°. The
adjustment points are eccentric washers grub screws 34
(model SN1435B).
Cutting Depth Calibration
Turn cutting depth buffer screw 35 to obtain a full cut of
the part worked on without the blade advancing too far
or damaging the part support strip (models SN1735 and
SN1470).
Blade Right Angle Calibration
Models SN1735 and SN1470 act on eccentric control 36
of the guide rollers to obtain a totally straight cut at right
angles to the cutting surface. It is recommended an official
technical service performs this adjustment.
In model SN 180 ( See FIG. E ) to adjust the straight cut.
Loosen the screw L to adjust the perpendicularity by acting
on the eccentric M. Apply the Allen screws P to ensure a
distance of at least 0.3mm with the band saw.
Fixed Cut Distance Buffer Adjustment
Only applicable to model SN1735. If parts are to be cut
with the same measurements, use the cut buffer formed
by parts 26 , 27 , 28 and 29 .
Screw rod 27 in hole 9 securing it with nut 26 ; loosen
wheel 28 and place retainer 29 at the distance necessary
from saw blade 6 ; tighten wheel 28 once again (only mod.
SN1735).
Part Size Limit
Cutting capacity
(mm)
SN 1435 B
90º ø125 125 125 x127
45º ø80 80 80x100
60º ø45 45 45x60
SN 1470
90º ø100 100 100x150
45º ø75 63 63x100
SN 1735
90º ø160 155 170x150
45º ø120 120 120x100
GENERAL USE INSTRUCTIONS
Failing to carry out the correct running in
procedure implies unavoidably compromising
saw blade cutting precision.
Running In
In order to achieve a better performance, the saw
blade, forming part of the machine, should undergo a
short running in procedure. Therefore, it is necessary to
perform the first 2 or 3 cuts on a full piece with Ø 40-
50mm, pressing softly on the part, slowly increasing this
in successive cuts.
4. MAINTENANCE AND SERVICE
INSTRUCTIONS
CLEANING
Disconnect the plug from the main socket before
commencing any maintenance operation on your machine.
Always wear personal protection means (glasses and
gloves) during maintenance operations.
Eliminate the residual shavings from production whenever
necessary, acting on the cutting area and on the guide/
blade. The use of a vacuum cleaner or a fine brush is
recommended.
Do not use compressed air due to the risk of harm
caused by shavings being projected.
If the band saw is not to be used for a long period, clean
and store it in a dry place. It is also recommended to
loosen the saw blade in order not to keep it tight for no
purpose.
REPAIR SERVICE
Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts.
Exploded views and information on spare parts can also
be found under: info@grupostayer.com
Our customer consultants answer your questions
conceming best buy, application and adjustment of
productsand accessories.
DISPOSAL AND RECYCLING
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
OnlyforEC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2012/19/
UE for Waste Electrical and Electronic
Equipment and its implementation into national
right,power tools that are no longer usable
must be collected separately and disposed of
in an environmentally correct manner.
Subject to change wlthout notlce.