stayer CM230K, Operating Instructions Manual

Page: 13 / 28

ENGLISH
9
9
SAFETY ISNTRUCTIONS
Please read these instructions carefully and keep
them.
WARNING! When using electric tools, basic safety
precautions should always be followed to reduced the
risk of fire, electric shock and personal injury,
including the following.
Read all there instructions before attempting to
operate this product and save these instructions.
For safe operations:
1. Keep work area clean - Cluttered areas and
benches invite injuries.
2. Consider work area environment - Do not
expose power area well lit. Don't use power tools in
presence of flammable liquids or gases.
3. Guard against electric shock – Prevent body
contact with grounded surfaces (e.g. pipes,
radiators, ranges refrigerators).
4. Keep children away – Do not let visitors contact
tool or extension cord. All visitors should be kept
away from work area.
5. Store idle tools – When not in use, tools should be
stored in dry, high or locked up place, out of reach
of children.
6. Don't force the tool – It will do the job better and
safer at the rate for which it was intended.
7. Use right tool – Don't force small tools or
attachments to do the job of a heavy duty tool. Don't
use tools for purposes not intended; for example,
don't use circular saw for cutting tree limbs or logs.
8. Dress properly – Do not wear loose clothing or
jewellery. They can be caught in moving parts.
Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear
protective hair covering to contain long hair.
9. Use safety glasses – Also use face or dust mask if
cutting operation is dusty.
10. Don't abuse cord – Never carry tool by cord or
yank it to disconnect it from receptacle. Keep cord
from heat, oil and sharp edges.
11. Secure work – Use clamps or a vise to hold work.
It's safer than using your hand and it frees both
hands to operate tool.
12. Don't overreach – Keep proper footing and
balance at all times.
13. Maintain tools with care - Keep tools sharp and
clean for better and safer performance. Follow
instructions for lubricating and changing
accessories. Inspect extension cords periodically
and replace if damaged. Keep handles dry, clean
and free from oil and grease.
14. Disconnect tools – When not in use, before
servicing, and when changing accessories such as
blades, bits and cutters.
15. Remove adjusting keys and wrenches – Form
the habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning
it on.
16. Avoid unintentional starting - Don't carry a
plugged – in tool with a finger on switch. Be sure
switch is off when plugging in.
17. Outdoor use extension cords – When tool is
used outdoors, use only extension cords intended
for use outdoors and so marked.
18. Stay alert – Watch what you are doing. Use
common sense. Do not operate tool when you are
tired.
19. Check damaged parts – Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced
by an authorised service center unless otherwise
indicated elsewhere in this instruction manual.
Have defective switches replaced by and
authorised service center. Do not use tool if switch
does not turn it on and off.
20. Warning – The use of any accessory or
attachment, other than recommended in this
operating instruction or the catalogue may present
a risk of personal injury.
21. Have your tool repaired by an expert – This
electric appliance is in accordance with the relevant
safety rules. Repairing of electric appliances my be
carried out only by experts otherwise it may cause
considerable danger for the user.
Save these instructions
SPECIFIC SAFETY RULES
- Always use safety chain. Mounting can release.
- The magnet's adhesion depends on the thickness
of the work piece. Always ensure that the work
piece is a minimum of 12mm (7/16 in.) thick. If it is
not, then use a piece of steel plate at least12mm
thick and larger than the magnet below the work
piece to supplement the magnetic adhesion.
- Metal chips and other debris will seriously hamper
magnetic adhesion. Always ensure that the magnet
is clean.
- Other units used on the same receptacle will cause
uneven voltage that could lead to the magnet
releasing. Always use the tool alone on the
receptacle.
- Other units used on the same receptacle will cause
uneven voltage that could lead to the magnet
releasing. Always use the tool alone on the
receptacle.
- Avoid the magnet releasing. Ensure that the
magnet has properly adhered to the work piece
before beginning drilling.
- Avoid operating annular cutters without coolant
fluid. Always check coolant level before operating.
- Do not operate with dull or damaged cutting tools.
This may overload the motor.
- Protect the motor. Never allow cutting fluid, water,
or other contaminants enter the motor.
- Metal chips are often very sharp and hot. Never
touch them with bare hands.