Stanley FATMAX SFMCMWS251, Original Instructions Manual

Page: 20 / 228

20
ENGLISH (Original instructions)
u
Sharpen blade at the original cutting angle.
u
Sharpen cutting edges on both ends of blade, removing
equal amounts of material from both ends.
To sharpen blade in a vise (Fig. K)
u
Be sure the bail handle is released, the blade has stopped
and safety key and battery packs are removed before
removing the blade.
u
Remove blade from mower. See instructions for Removing
and Installing Blade.
u
Secure blade (26) in a vise (28).
u
Wear proper eye protection and gloves and be careful not
to cut yourself.
u
Carefully file the cutting edges of the blade with a fine
tooth file (29) (not included) or sharpening stone (not
included), maintaining the angle of the original cutting
edge.
u
Check balance of blade. See instructions for Blade
Balancing.
u
Replace blade on mower and tighten securely.
Blade balancing (Fig. L)
Check balance of the blade (26) by placing center hole in the
blade over a nail or round screwdriver , clamped horizontally
in a vise (28). If either end of the blade rotates downward, file
along the sharp edge of that dropping end. Blade is properly
balanced when neither end drops.
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
u
Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com.
Technical data
SFMCMWS251
Voltage Vdc 2 x 18
No-Load Speed min
-1
2800
Weight kg 20
Blade length mm 492
Battery SFMCB204
Voltage V 18
Capacity Ah 4.0
Type Type 1
Charger SFMCB12
Input Voltage V
AC
230
Output Current A 2.0
Approx. charge time h 2
Hand/arm weighted vibration value:
= <2.5 m/s
2
, uncertainty (K) = 1.5m/s
2
.
L
PA
(emission sound preasure) 73 dB(A)
uncertainty (K) = 3 dB(A)
EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
%
SFMCMWS251 lawn mower
STANLEY FATMAX declares that these products described
under "technical data" are in compliance with:
2006/42/EC, EN60335-1:2012 + A11:2014 + A13:2017 +
A1:2019 + A14:2019 + A2:2019, EN60335-2-77:2010.
2000/14/EC, Lawn Mower, L < 50cm, Annex VI,
DEKRA Testing and Certification GmbH,
Handwerkstraße 15, 70565 Stuttgart
Location Certification Body,
Dinnendahlstr. 9, 44809 Bochum Germany
Notified Body number: 0158
L
WA
(measured sound power level) 83 dB(A),
Uncertainty (K) = 0.9 dB(A),
L
WA
(guaranteed sound power) 88 dB(A).