10
ü
Wind threshold is to high. Adjust the threshold.
ü
The device could be installed in a position little exposed to the wind.
ü
The wind sensor may be damaged. Check the functioning by turning the cups to simulate the presence of the wind and make sure that device enter in "wind
alarm”.
IN PRESENCE OF WIND, THE UPWARD MOVEMENT IS NOT COMMANDED.
12. FAQ
ü
Verify the power supply.
ü
Once powered, the device lights LEDs briefly to indicate the proper power supply. If this doesn't happen, it is likely a fault and it may be necessary to replace
the device.
ü
The connection of the wires of the motor windings is reversed. Remove power to the device and reverse the motor wires connected to the wires
3
and
4
.
THE DEVICE DOESN’T WORK.
WHEN I PRESS UP, THE MOTOR MOVES DOWN.
ü
Be sure to have correctly done the memorization procedure.
ü
The procedure has been made too slowly. When device entries into “transmitter programming” mode, you have 15 sec to press the STOP button of the
transmitter you want to store.
ü
Verify that battery of the remote control are charged.
ü
Try to do the same operation with another transmitter.
ü
Check that the environment is not disturbed by other devices working at the same frequency (for example alarms, radio earphones..).
ü
Make a reset of the device and try again to memorize the transmitter.
ü
The receiver of the device could be damage and could be necessary a device replacement.
ü
Verify that stored remote control operates correctly.
ü
Be sure to have correctly done the memorization procedure.
ü
The device has memorized the maximum number of storable transmitters.
ü
The procedure has been made too slowly. When device entries into “transmitter programming” mode, you have 15 sec to press the STOP button of the
transmitter you want to store.
ü
Verify that battery of the remote control are charged.
ü
Try to do the same operation with another transmitter.
ü
Check that the environment is not disturbed by other devices working at the same frequency (for example alarms, radio earphones..).
ü
Make a reset of the device and try again to memorize the transmitter.
ü
The receiver of the device could be damage and could be necessary a device replacement.
WHEN I TRY TO STORE THE FIRST REMOTE CONTROL, MOTOR MAKES 2 DOWNWARD MOVEMENTS.
WHEN I TRY TO STORE ANOTHER TRANSMITTER, MOTOR MAKES 2 DOWNWARD MOVEMENTS.
ü
Be sure to have correctly done the delete procedure.
ü
The process has been made too slowly. When the central unit entries into “transmitter setting” mode, there are 15 sec to press the STOP key of the
transmitter to store.
ü
The device has only one transmitter in its memory: this cannot be deleted!
WHEN I TRY TO DELETE A TRANSMITTER FROM THE MEMORY, MOTOR MAKES 2 DOWNWARD MOVEMENTS.
All rights reserved.
STAFER S.p.a. - via Malpighi, 9 - 48018 Faenza (RA) ITALY
Tel. (+39) 0546.624811 - Fax. (+39) 0546.623141 - www.stafer.com
ü
The device is in “Wind alarm”.
ü
Sun threshold is too high. Adjust the threshold.
ü
The device could be installed in a position little exposed to the sun, or some object obstructs the proper detection of the sun.
ü
Sun function is deactive.
ü
The sun sensor may be damaged. Check functionality by checking that "sun LED" blinks quickly once you apply a warm light source at the oval on the
device.
IN PRESENCE OF WIND, THE UPWARD MOVEMENT IS COMMANDED BUT IN PRESENCE OF SUN THE DOWNWARD MOVEMENT IS NOT
COMMANDED
All products and technical specifications given in this document are subject to variation without notice. Unless previously and specifically authorised by STAFER, the device must be
used exclusively with transmitters produced by STAFER.
STAFER cannot be consider responsible for damage caused by improper, incorrect or unreasonable uses.
