background image

06

07.  MEMORIZATION/DELETION OF A TRANSMITTER

Bring motor in a 

intermediate position

A

Motor makes 2 upward 

movements

D

OFF

ON

Switch OFF power supply, 

wait 2 seconds and switch ON 

power supply.

B

10 x DOWN

Within 15 seconds press 

DOWN 10 times.

C

x2

07.1 USING COMMAND BUTTONS

RAIN SENSOR

P2

(1)

HANDHELD TRANSMITTER

WITHIN 15 SECONDS PRESS:

STOP

P2

E

To memorize a transmitter, in addition to the onboard buttons (see section 05, "How to memorize the first handheld transmitter"), you can use the command 
buttons or, for added convenience, an already stored handheld transmitter. 
If the transmitter is already stored in the device, by performing the procedure the transmitter is deleted from the memory.

The motor signals the operation 

performed

F

MEMORIZED

DELETED

x1

x1

Notes:

ü

(1): the button must be pressed briefly (less than 0.5 sec) and in rapid succession (max 1 seconds between each press and the next).

ü

(2): If the button is not pressed within 15 seconds, the motor exits the programming and signals it with 2 downward movements

ü

The device can memorize up to 15 radio codes (including rain sensors) for each motor. The condition of 'memory full' is reported with 2 downward 
movements

ü

If the motor has memorized a single hand-held transmitter, it can't be deleted (the non-cancellation is indicated by two downward movements).

(1)

(2)

Bring motor in a 

intermediate position

A

Motor makes 2 upward 

movements

B

C

x2

07.2 USING AN HAND-HELD TRANSMITTER

RAIN SENSOR

P2

(1)

HANDHELD TRANSMITTER

WITHIN 15 SECONDS PRESS:

STOP

P2

D

The motor signals the operation 

performed

E

MEMORIZED

DELETED

x1

x1

Notes:

ü

(1): If the button is not pressed within 15 seconds, the motor exits the programming and signals it with 2 downward movements

ü

The device can memorize up to 15 radio codes (including rain sensors) for each motor. The condition of 'memory full' is reported with 2 downward 
movements

ü

If the motor has memorized a single hand-held transmitter, it can't be deleted (the non-cancellation is indicated by two downward movements).

(1)

Press and hold PROG of a transmitter already memorized for 

about 5 sec. 

By mod. 593

By mod. 594

Summary of Contents for 593.K.RS.00












Reviews: