07
Notes:
ü
(1) : press the buttons within 10 seconds from the last flash of LED 1. The buttons must be shortly pressed, around 1 second between two pressures.
Press the buttons the same number of time of the desired value: e.g. press 8 times P3 to set 8 Km/h; press 2 times P1 to set 20 Km/h; press 2
times P1 and 8 times P3 to set 28 Km/h.
ü
If you try to set a wind threshold lower than 5 Km/h or higher than 35 Km/h, the device signals the error with the lighting of the 3 leds for 3 times.
If the wind speed is above the set threshold for at least 3 seconds, an upward movement is commanded to protect the awning (wind alarm). During this phase
all
manual commands are disabled
. The device exits from the “wind alarm” if the wind speed keeps below the set threshold for at least 8 minutes. The wind
threshold is varying from 5 km/h to 35 km/h. The factory sets the wind threshlod at 15 Km/h.
08. WIND SENSOR
08.1 CHANGING THE WIND THRESHOLD USING THE ONBOARD BUTTONS
Press P3 until LED 3 lights ON
Press P1 to set the tens and P3 to set the units
The device signals the new value and exits from
programming
LED 3 turns off and LED 1 indicates the current value of the wind
threshold
If the value is the
desired one, wait
10 seconds:
the device signals
again the value
and exits from the
programmation.
B
D
E
C
During the installation phase, it is possible to exit from “wind alarm” without waiting 8 minutes below the threshold, shortly pressing (less than 1 sec) any of the
buttons
P1
,
P2
,
P3
on the device.
LED Wind
→
RED
:
the wind is above the threshold.
LED Wind
→
OFF
:
the wind is below the threshold.
LED Manoeuvre
→
QUICK FLASHES
LED Sun
→
RED
08.4 FORCED EXIT FROM THE WIND ALARM
}
08.3 VISUAL SIGNALS ASSOCIATED WITH THE WIND SENSOR
Bring motor in a
intermediate position
Bring motor in a
intermediate position
A
A
P3
EXAMPLES:
TO ADJUST THE WIND THRESHOLD:
1 flash
1 flash
10
18 Km/h
pause
pause
5 flashes
8 flashes
5 flashes
10 + 5 = 15 Km/h
10 + 8 = 18 Km/h
5 Km/h
+
+
+
+
P3
P1
1 X
8 X
+
+
=
8
EXAMPLE:
(1)
08.2 CHANGING THE WIND THRESHOLD USING AN HANDHELD TRANSMITTER
:the module is in wind alarm and the manual commands are disabled.
01. Select the correct radio channel and bring the motor
on the intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on the
display.
03. Press 1 time
NEXT
. 01 appears on the display.
04. Press 1 time
STOP
.The receiver signal the current
value.
Examples:
if threshold = 08 Km/h:
p
8 (8 short movements)
if threshold = 15 Km/h:
p
1 - pause -
p
5
if threshold = 30 Km/h:
p
3 - pause -
p
1 long
05. Using
PREV
and
NEXT
to set the new value. (from 5
Km/h at 35 Km/h. From factory set to 15 Km/h).
Examples:
for threshold 08 Km/h: (0 time PREV) - 8 times NEXT
for threshold 15 Km/h: 1 time PREV - 5 times NEXT
for threshold 30 Km/h: 3 times PREV - (0 time NEXT)
06. Press 1 time
STOP
.The receiver signal the new
value.
B.1
USING AN HAND-HELD TRANSMITTER Mod.594
B.2
USING AN HAND-HELD TRANSMITTER Mod.593
01. Bring the motor to the intermediate position.
02. While press STOP also press PROG for until the LED
lights up.
03. Press once
DOWN
.
04. Press once
STOP
. The motor shows the current value
Examples:
if threshold = 08 Km/h:
p
8 (8 short movements)
if threshold = 15 Km/h:
p
1 - pause -
p
5
if threshold = 30 Km/h:
p
3 - pause -
p
1 long
05. Using
PREV
and
NEXT
to set the new value. (from 5
Km/h at 35 Km/h. From factory set to 15 Km/h).
Examples:
for threshold 08 Km/h: (0 time PREV) - 8 times NEXT
for threshold 15 Km/h: 1 time PREV - 5 times NEXT
for threshold 30 Km/h: 3 times PREV - (0 time NEXT)
06. Press 1 time
STOP
.The receiver signal the new
value.
