09
LED Sun
→
RED
: the function is not active or wind alarm in progress (the sun function is temporarily disables)
LED Sun
→
OFF
: the intensity of the sun is below the set threshold
LED Sun
→
GREEN
: the intensity of the sun is above the set threshold
The "LED manoeuvre" provides information on the latest manoeuvre performed automatically by the device:
LED Manoeuvre
→
OFF
: an automatic upward movement was performed for absence of sun
LED Manoeuvre
→
GREEN
: an automatic downward movement was performed for presence of sun
LED Manoeuvre
→
SLOW FLASHES
: the device is just turned on or is just exit from wind alarm and has not yet made any automatic operation concerning the
sun
LED Manoeuvre
→
FAST FLASHES
: wind alarm in progress
09.5 VISUAL SIGNALS ASSOCIATED TO SUN FUNCTION
11. RESET
A
B
C
This procedure restore the factory condition. This procedure should only be performed by qualified service personnel. After
performing the reset procedure, the technician must promptly arrange to carry out the installation described in Section 5.
P1
P3
Press at the same time
P1
and
P3.
Hold the buttons. After a few seconds the
three leds start flashing.
Hold
P1
and
P3
for around 30 sec, the three leds light on.
D
P1
P3
P1
P3
P1
P3
The motor performs two short alternating
movements to indicate the occurred reset.
The device is provided with a diagnosis function of the wind sensor. If, for about 24 hours the wind sensor does not generate any valid pulse, the device
commands an automatic upward manoeuvre, suspends all other activities and indicates the fault by flashing the LEDs. The device will come out of this state
resuming normal activities only when the wind sensor generates a valid pulse. The factory sets this test "inactive".
To change the setting:
10. ANEMOMETRIC TEST
Bring motor in a
intermediate position
A
B.1
01. Select the correct radio channel and bring the motor on
the intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on the
display.
03. Press 1 TIME
PREV
and 6 times
NEXT
. 16 appears on
the display.
04. Press 1 time
STOP
. The receiver signals the current
value.
Function active:
p
1
(1 short upward movement)
Function not active:
q
1
(1 short descent movement)
05. Press
PREV
to disable the function (
Of
appears on the
display) or
NEXT
to enable the function (
On
appears on
the display). Factory set is Of.
06. Press 1 time
STOP
. The receiver signal the new value.
Function active:
p
1 - Function not active:
q
1
Bring the motor in an
intermediate position
A
B.1
01. Select the correct radio channel and bring the motor
on the intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on
the display.
03. Press 2 times
NEXT
. 02 appears on the display.
04. Press 1 time
STOP
. The receiver signals the current
value. Examples:
if threshold = 07 Klux:
p
7 (7 short movements)
if threshold = 18 Klux:
p
1 - pause -
p
8
if threshold = 20 Klux:
p
2 - pause -
p
1 long
05. Using
PREV
and
NEXT
to set the new value (from 1
Klux at 45 Klux. From factory set to 16 Klux).
Examples:
for threshold 07 Klux: (0 time PREV)-7 timesNEXT
for threshold 18 Klux: 1 time PREV-8 times NEXT
for threshold 20 Klux: 2 times PREV-(0 time NEXT)
06. Press 1 time
STOP
. The receiver signal the new
value.
B.2
USING AN HAND-HELD TRANSMITTER Mod.593
USING AN HAND-HELD TRANSMITTER Mod.594
USING AN HAND-HELD TRANSMITTER Mod.594
B.2
USING AN HAND-HELD TRANSMITTER Mod.593
01. Bring the motor to the intermediate position.
02. While press STOP also press PROG for until the
LED lights up.
03. Press twice
DOWN
.
04. Press once
STOP
. The motor shows the current
value Examples:
if threshold = 07 Klux:
p
7 (7 short movements)
if threshold = 18 Klux:
p
1 - pause -
p
8
if threshold = 20 Klux:
p
2 - pause -
p
1 long
05. Using
UP
and
DOWN
to set the new value (from 1
Klux at 45 Klux. From factory set to 16 Klux).
Examples:
for threshold 07 Klux: (0 time PREV) - 7 times NEXT
for threshold 18 Klux: 1 time PREV - 8 times NEXT
for threshold 20 Klux: 2 times PREV - (0 time NEXT)
06. Press 1 time
STOP
. The receiver signal the new
value.
01. Bring the motor to the intermediate position.
02. While press STOP also press PROG for until the
LED lights up.
03. Press once
UP
and 6 times
DOWN
.
04. Press 1 time
STOP
. The receiver signals the
current value.
Function active:
p
1
(1 short upward movement)
Function not active
:
q
1
(1 short descent
movement)
05. Press
DOWN
to disable the function
Press
UP
to enable the function
06. ress 1 time
STOP
. The receiver signal the new value.
Function active:
p
1 - Function not active:
q
1
