STA-RITE INTELLIPRO 2 VST Installation And User Manual Download Page 11

Page: 11 / 36

INTELLIPRO

2 VST Variable Speed Pump Installation and User’s Guide

Operator Control Panel: Pump Menu Guide

Press MENU button to access menus

Date

Pump Address (1-16) - Default: 1
Screen Contrast (1-5) - Default: 3
Language

Manual
Schedule

Egg Timer

Set Speed - Default Spd 1-2: Manual
Set Speed

Set Start Time

Set Stop Time
Set Speed - Default Spd 3-4: Egg Timer

Time

Disabled / Enabled - Default: Enabled

Schedule

Set Speed

Set Start Time

Set Stop Time

Disabled

Default: Disabled

40° F - 50° F (4.4° C through 10° C) Default: 40° F (4.4° C)

Set Speed (450 RPM - 3450 RPM) Default 1000 RPM

SETTINGS

MENU

SPEED 1-8

EXT CONTROL

THERMAL MODE

Time

Hour Format

Months (1-12)
Days (1-31)
Years (2000-2050 Plus)

Hours (24hr Mode: 0-23) (12hr Mode: 1-12 AM & PM)
Minutes (0-60)

AM/PM - Default: AM/PM

Min Speed (450-1700 RPM) - Default: 450 RPM
Max Speed (1900-3450 RPM) - Default: 3450 RPM

English - Default: English
Português
Deutsch
Italiano
Nederlands

Français

Español

Temperature Unit

Fahrenheit - Default F°
Celsius C°

Firmware Version

Password

Disabled - Default: Disabled
Enabled

Password Timeout (1 min. to 6 hrs.) - Default: 1 minute
Set Password (0000 - 9999) - Default: 1234

Stop Delay (0 min. to 10 min.) Default: 0 minutes

24 Hour

Device

Set Date and Time

Set Speed Max/Min

Speed 1-4

Speed 5-8

Disabled/Enabled

Set Speed

Pump Temperature

(pages 8-10)

(pages 10-12)

(page 12)

(page 16)

Set Speed (450-3450 RPM) - Default: 750 RPM

Set Speed (450-3450 RPM) - Default: 1500 RPM

Set Speed (450-3450 RPM) - Default: 2350 RPM

Set Speed (450-3450 RPM) - Default: 3110 RPM

Program 1

Program 2

Program 3

Program 4

Set Speed (450-3450 RPM) Default: 3450 RPM
Quick Clean Duration (1 min. to 10 hrs.) Default: 10 minutes

Time Out Duration (1 min. to 10 hrs.) Default: 3 hours

FEATURES

Quick Clean

Time Out

(page 13)

(1 min. to 30 min.) Default: 11 minutes

Disabled / Enabled - Default: Enabled

(1 - 10) Default: 5

(1 sec. to 10 min.) Default: 20 seconds

PRIMING

Disabled/Enabled

Max Priming Time

Priming Range

Priming Delay

(pages 13-15)

Priming Speed

Set Speed (2400-3450 RPM) - Default: 3450 RPM

Alarm Log (1-10)

Stop Delay (0 min. to 10 min.) Default: 0 minutes

Summary of Contents for INTELLIPRO 2 VST





































Search results

Summary of Contents for INTELLIPRO 2 VST

Reviews:

Related manuals for INTELLIPRO 2 VST

Brands by name

Popular brands

STA-RITE INTELLIPRO 2 VST, Installation And User Manual

Search results

Summary of Contents for INTELLIPRO 2 VST

Reviews:

Related manuals for INTELLIPRO 2 VST

Brands by name

Popular brands