SP Scientific Freezemobile Series Operator'S Manual Download Page 20

Sentry 2.0 Controls 

VirTis Freezemobile 25L and 35L

 
 

10 

 

Rev 005, 02/12 

 

 

© SP Scientific 2012 

Bath (Optional) 

Enabling the Bath function directs cooling to the optional Shell Bath module for 
freezing products prior to freeze-drying. The temperature of the bath will be displayed 
on the Synoptic screen. 
 

Note: This feature will only be displayed if a factory-installed Shell Bath module was purchased 
with your unit. 

 

Purge (Optional) 

Enabling the Purge function closes the purge valve located between the vacuum 
pump and the suction port of the unit. This allows a high vacuum to be pulled within 
the volume between the pump and the valve without the entire unit being under 
vacuum. The gas ballast within the pump can then be opened to cleanse the pump oil. 
 

Note: This feature will only be displayed if the purge option was purchased with your unit. 
 

Heat (Optional) 

The Heat function gives the ability to add controlled heat to product shelves for 
enhanced drying. If installed, you can set the temperature of the manifold shelves up 
to 50 °C. 
 

Note: This feature will only be displayed if the shelf heat option was purchased with your unit. 
 

User Options 

To access the User Options, select User Options from the Main Menu and press the 
Menu button. 

     User Options 

 

Vacuum Control              VLC  

Temperature Units             C 

Vacuum Units               Torr 

Relay Test                    

 

Vacuum Pump Maintenance       

 

 

Vacuum Control 

The Vacuum Control field sets the method used for vacuum level control: None, VLC 
or Power Save.  

 

Setting Vacuum Control to None disables vacuum level control.  

 

Setting Vacuum Control to VLC allows gas to bleed into the system through a 
control valve to maintain the vacuum setpoint.  

 

Setting Vacuum Control to Power Save isolates the system and maintains 
pressure by shutting off power to the vacuum pump and VBS valve. As the 
system pressure rises, the vacuum pump is re-energized and the system is 
pulled back down. To avoid rapid cycling of the vacuum pump, the Power 
Save Deadband should be set to 20 or more. 

Summary of Contents for Freezemobile Series























































Reviews: