Sourcetronic ST2826 Operation Manual Download Page 69

Page: 69 / 145

ST2826 Operation manual

Ver1.0

◇

field will display A, the cursor will be moved to the LOW field

automatically.

Press [3][2][5], +325 will be displayed in the bottom line of the screen.

The usable units (p, n, u, m and MORE 1/2) will be displayed in the

softkey area. Press n, the value of the field will be changed to 325.000n.

The cursor will be moved to the HIGH field of the sweep point 1

automatically.

Press [3][3][3], +333 will be displayed in the bottom line of the screen.

The usable units (p, n, u, m and MORE 1/2) will be displayed. Press n, the

value of this field will be changed to 333.000n. The cursor will be moved

to the parameter area of the sweep point 2.

Press [10], +10 will be displayed in the bottom line of the screen. The

usable units (Hz, kHz and MHz) will be displayed in the softkey area.

Press kHz, the value of this field will be changed to 10.0000k.

Press [ ]. Move the cursor to the LMT field of the sweep point 2.

Current field displays , the softkey area will display LIMIT DATA A,

LIMIT DATA B and OFF.

Press LIMIT DATA B to select the secondary compared parameter D. The

field will display , the cursor will be moved to the LOW field of the

sweep point 2 automatically.

Press [0][.][0][0][0][1], +0.0001 will be displayed in the bottom line of the

screen. The usable units (p, n, μ, m and MORE 1/2) will be displayed in

the softkey area. Press MORE 1/2. k, M, *1 and MORE 2/2 will be

displayed. Press *1, the value of this field will be changed to 100.000μ.

The cursor will be moved to the HIGH field of the sweep point 2

automatically.

Press [0][.][0][0][0][3], +0.0003 will be displayed in the bottom line of the

screen, the usable units (k, M, *1 and MORE 2/2) will be displayed in the

softkey area. Press *1, the value of the field will be changed to 300.000μ.

The cursor will be moved to the parameter area of the sweep point 3.

According to steps l to p, Input the parameters of sweep point 3 in turn:

100 kHz, B, 0.0060 and 0.0100.

3) Setting for alarm

(a)Press [SYSTEM]. The SYSTEM SETUP page will be displayed.

(b)Move the cursor to beep field. The current field displays LOW. OFF, LOW and HIGH

will be displayed in the softkey area.

(c)Press HIGH to select beep with high sound

Summary of Contents for ST2826


















































































































































Search results

Summary of Contents for ST2826

Reviews:

Brands by name

Popular brands

Sourcetronic ST2826, Operation Manual

Search results

Summary of Contents for ST2826

Reviews:

Brands by name

Popular brands