Sony Handycam DCR-TRV230E, Service Manual

Page: 185 / 242

5-44
3-3. SERVO AND RF SYSTEM ADJUSTMENT
Before perform the servo and RF system adjustments, check that
the specified value of “36MHz Origin Oscillation Adjustment” of
“VIDEO SYSTEM ADJUSTMENT” is satisfied.
Adjusting Procedure:
1.
REEL FG adjustment
2. PLL fo & LPF fo pre-adjustment
3. Switching position adjustment
4. AGC center level and APC & AEQ adjustment
5. PLL fo & LPF fo fine adjustment
6. Hi8/Standrd8 switching position adjustment
7. CAP FG offset adjustment
1. REEL FG Adjustment (VC-254 board)
Compensates the dispersion of the hall elements.
Measurement Point Display data of page: 3, address: 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 17, 30
Specified Value 00 or 01 or 04 or 05
Adjusting method:
Order Page Address Data Procedure
1 Close the cassette compartment
without inserting a cassette.
2 0 01 01 Set the data.
3 3 01 1C Set the data, and press PAUSE
button.
4 3 02 Check that the data changes to
“00”,
5 3 03 Check that the data is “00” or
“01” or “04” or “05”. (Note)
6 0 01 00 Set the data.
Note: If the data is other value, adjustment has errors. (Take an appropriate
remedial measures according to the errors referring to the following
table.)
Data Contents of defect
02, 03, 06, 07 T reel is defective
08, 09, 0C, 0D S reel is defective
0A, 0B, 0E, 0F S reel and T reel are defective
2. PLL fo & LPF fo Pre-Adjustment (VC-254 board)
Mode VTR stop
Measurement Point Display data of page: 3, address: 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 1F, 20, 22, 29
Specified Value The data of page: 3, address: 02 is “00”.
The data of page: 3, address: 03 is “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 3 01 00 Set the data, and press PAUSE
button.
3 3 01 30 Set the data, and press PAUSE
button.
4 3 02 Check that the data changes to
“00” within 10 sec. (Note)
5 3 03 Check that the data is “00”. (Note)
6 0 01 00 Set the data.
Note: If it isn’t satisfied, select page: C, address: 21, set the following
data, and press the PAUSE button, and repeat steps 2 to 4.
Setting data
When the data of page: C, address: 21 is “CA”. CE
When the data of page: C, address: 21 is “CE”. C6
When the data of page: C, address: 21 is “C6”. D2
When the data of page: C, address: 21 is “D2” C2
If bit2, bit3, bit4, bit5 or bit6 of page: 3, address: 03 data is “1”,
there are errors.
For the error contents, see the following table. (For the bit values,
refer to “5-4. SERVICE MODE”, “4-3. 3. Bit value discrimination”.)
Bit value of page: 3, Error contents
address: 03 data
bit 2 = 1 or bit 3 = 1 PLL fo fine adjustment is defective
bit 4 = 1 or bit 5 = 1 PLL fo adjustment is defective
bit 6 = 1 LPF fo is defective