Sony DVP-NS47P - Cd/dvd Player Service Manual Download Page 9

Page: 9 / 86

1-4

DVP-NS47P/NS57P/NS508P/NS64P/NS67P/NS608P

kups

Step 3: Connecting the Audio Cords

Select one of the following patterns

, according to the input jack on your TV monitor,

projector, or audio component such as an AV amplifier (receiver).
This will enable you to listen to sound.

Hint

For correct speaker location, see the operating instructions supplied with the connected components.

VIDEO

AUDIO

INPUT

COAXIAL

OPTICAL

DIGITAL OUT

Audio component
with a decoder

(red)

TV, projector, or
audio component

Audio/video
cord (supplied)

: Signal flow

Coaxial digital cord
(not supplied)

to DIGITAL OUT
(COAXIAL or OPTICAL)

to LINE OUT L/R (AUDIO)

Rear (L)

CD/DVD player

(white)

(yellow)

(white)

(red)

[Speakers]

Front (L)

[Speakers]

to coaxial
digital input

Rear (R)

Front (R)

Subwoofer

Centre

* The yellow plug is used for video signals (page 14).

Optical digital cord
(not supplied)

to optical
digital input

continued

Audio L/R input jacks

This connection will use your TV’s or audio
component’s two speakers for sound.

Digital audio input jack

If your audio component has a Dolby*

Digital, DTS*

, or MPEG audio decoder and

a digital input jack, use this connection. You
can enjoy Dolby Digital (5.1ch), DTS
(5.1ch), and MPEG audio (5.1ch) surround
effect.

Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #:
5,451,942 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Out are
registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-
2007 DTS, Inc. All Rights Reserved.

Notes

• After you have completed the connection, make

the appropriate settings in Quick Setup (page 19).
If your audio component has an MPEG audio
decoder function, set “MPEG” to “MPEG” in
AUDIO SETUP (page 54). Otherwise, no sound
or a loud noise will come from your speakers.

• The TVS effects of this player cannot be used

with this connection.

• In order to listen to DTS sound tracks, you must

use this connection. DTS sound tracks are not
output through the LINE OUT L/R (AUDIO)
jacks, even if you set “DTS” to “ON” in Quick
Setup (page 19).

kups

Step 4: Connecting the Mains Lead

Plug the player and TV mains lead (power cord) into a mains.

Step 5: Preparing the Remote

You can control the player using the supplied remote. Insert two R6 (size AA) batteries by
matching the

and

ends on the batteries to the markings inside the compartment. When

using the remote, point it at the remote sensor

on the player.

Notes

• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a

malfunction.

• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage

from battery leakage and corrosion.

continued

Controlling Your TV with the
Supplied Remote

You can control the sound level, input source,
and power switch of your Sony TV with the
supplied remote.

You can control your TV using the buttons
below.

Note

Depending on the connected unit, you may not be
able to control your TV using all or some of the
buttons on the supplied remote.

Controlling other TVs with the
remote

You can control the sound level, input source,
and power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer’s code.

While holding down TV

[

, press the

number buttons to select your TV’s
manufacturer’s code (see the table
below).

Release TV

[

Code numbers of controllable TVs

If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.

◆

For RMT-D175P/RMT-D185P remote

commander only

◆