5-33
DCR-TRV40/TRV40E/TRV50/TRV50E
17. Strobe Light Level Adjustment
Adjust the light level when the strobe light flashes.
Subject
Paper which reflection rate is 18%
(50cm from the front of the lens)
(Note1)
Adjustment Page
F
Adjustment Address
8C to 91
Specified Value
Data of page: 6, address: B8 is “00”.
Note1:
Background paper (J-250-130-A). Perform this adjustment in the
dark room or use a dark box.
Note2:
Any light other than the strobe light should not light up the plate.
Note3:
This adjustment should be carried out upon completion of “HALL
Adjustment” , “Flange Back Adjustment”.
Note4:
The data of page: 0, address: 10 must be “00”.
Note5:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1)
POWER .................................................................. CAMERA
2)
FLASH ......................................................................... OPEN
(Press FLASH ( ) button and set to the forced flash mode ( ),
and press PHOTO button.)
3)
NIGHT SHOT .................................................................. OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
7
05
04
Set the data. (Note6)
3
6
01
67
Set the data, and press PAUSE
button.
4
Check the flashing.
5
6
02
Check that the data is “01”. (Note7)
6
6
B8
Check that the data is “00”.
Note6:
Use the STOP button of the adjustment remote commander.
Note7:
The adjustment data will be automatically input to page: F, address:
8C to 91.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
2
7
05
00
Set the data.
3
0
01
00
Set the data.
18. Strobe White Balance Adjustment & Check
Adjust and check the white balance when the strobe light flashes.
Subject
Paper which reflection rate is 18%
(50cm from the front of the lens)
(Note1)
Measurement Point
Video output terminal
Measuring Instrument
Vectorscope
Adjustment Page
F
Adjustment Address
3E, 3F
Specified Value
Fig. 5-1-14.
Note1:
Background paper (J-250-130-A). Perform this adjustment in the
dark room or use a dark box.
Note2:
Any light other than the strobe light should not light up the plate.
Note3:
This adjustment should be carried out upon completion of “HALL
Adjustment”, “Flange Back Adjustment”, “Auto White Balance
& LV Standard Data Input”, “Auto White Balance Adjustment”,
“Strobe Light Level Adjustment”
Note4:
The data of page: 0, address: 10 must be “00”.
Note5:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1)
POWER .................................................................. CAMERA
2)
FLASH ......................................................................... OPEN
(Press FLASH ( ) button and set to the forced flash mode ( ),
and press PHOTO button.)
3)
NIGHT SHOT .................................................................. OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
7
05
04
Set the data. (Note6)
3
6
01
B9
Set the data, and press PAUSE
button.
4
Check the flashing.
5
6
02
Check that the data is “01”. (Note7)
6
6
02
00
Set the data.
7
6
01
E7
Set the data, and press PAUSE
button.
8
Check the flashing.
9
6
02
Check that the data is “01”.
10
Wait for 3 sec.
11
Check that the center of the
white luminance point is within
the circle shown Fig. 5-1-13. A.
Note6:
Use the STOP button of the adjustment remote commander.
Note7:
The adjustment data will be automatically input to page: F, address:
3E, 3F.
Processing after Completing Adjustments:
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
2
7
05
00
Set the data.
3
0
01
00
Set the data.
R-Y
2mm
B-Y
2mm
Fig. 5-1-14.
