manualshive.com logo in svg

Sonnen sonnenBatterie eco 8.0, Installation Instructions Manual, Page: 26 / 63

Share
Download
Sonnen sonnenBatterie eco 8.0 Installation Instructions Manual Download Page 26

6

Electrical connection

6  Electrical connection

Danger to life due to electrocution!

The following points must be observed when carrying out electrical work on the 
storage system or on the electrical distributor:

► 

Switch off the storage system.

► 

Disconnect the relevant electrical circuits.

► 

Secure against anyone switching on the device again.

► 

Check that the device is disconnected from the power supply.

► 

Only authorised electricians are permitted to carry out electrical work.

Touch voltage in the event of a fault

Danger to life due to electrocution!

► 

Install residual current devices (RCDs) upstream of the storage system.

The rated differential current of the residual current device (RCD) must be 
30 mA. The type of RCD used must be adapted to suit on-site conditions. If no 
special type is required, a type A residual current device (RCD) can be used. 

Observe the maximum line lengths.

None of the lines connected to the storage system (electrical power, Ethernet 
line, Modbus line, other data lines, etc.) are allowed to exceed a maximum length 
of 30 m.

page 26 of 63

 

KD-291 | Part no. 52187 | EN | X01

CAUTION

DANGER

WARNING

Notice

CAUTION

DANGER

WARNING

Notice

CAUTION

DANGER

WARNING

Notice

Heruntergeladen von

 

manualslib.de

 

Handbücher-Suchmachiene

 

Summary of Contents for sonnenBatterie eco 8.0
































































Reviews:

No comments