Sonifex DHY-03 User Handbook Manual Download | Manualshive

Page: 54 / 56

background image

40

DHY-03 User Handbook

TECHNICAL SPECIFICATION

Accessories

Order Code

Description

DHY-03CON

Convert rack-mounted to free standing

DHY-03SCON

Front panel conversion kit, DHY-03 free standing to DHY-03S 19” rack-
mount front

DHY-03TCON

Front panel conversion kit, DHY-03 or DHY-03S, to DHY-03T 19” rack-
mount front

DHY-03CONF

Conference cable, 0.5m long

DHY-03RLY

Automatic handset divert relay (for older hybrids, see below)

Table 4-3 : Accessories.

Divert Relay Function

The divert relay will disconnect the handset from the line when the call is being handled by
the DHY-03. For the DHY-03EC and for later models of the DHY-03 (serial numbers 507 - 581
and 600 onwards) this relay is fitted internally. To disable the divert relay use the serial port
to set parameter 2 to just the DTMF select value (default DTMF is * so parameter 2 is 13 or
0D hex). For earlier models (serial numbers 1-506 & 582-599) the function is provided by the
optional external divert relay unit (DHY-03RLY) and is enabled by setting parameter 2 to 17
(or 11 hex).

Approvals Information

Sonifex is a BABT approved manufacturing facility with a license to build
telecommunications equipment and all telecom products are compliant with BS6301,
BS7002, BS415 and CTR21. The following product description is necessary for BABT approval
and provides information on the connection and operating conditions of the units.

Manufacturer

Sonifex Limited, 61 Station Road, Irthlingborough, Northants, NN9 5QE, United Kingdom

Equipment Type

DHY-03 telephone balance unit.

Approval File Reference

SON: TJF 25

Functions

The DHY-03 Telephone Balance Unit is suitable for connection to B.T. exchange lines with a
parallel connected telephone at the handset port. The hybrid unit is used as a four wire to
two wire converter. Incoming calls received at the handset may be diverted to the hybrid
unit and produce a ‘telephone’ signal at the output of the unit. Signals presented at the
input are transmitted to the telephone line only. The DHY-03 automatically balances the
telephone line.

TECHNIC

AL SPECIFIC

A

TION

4

«
...
52
53
54
55
56
»

Summary of Contents for DHY-03

























































Reviews:

No comments

Related manuals for DHY-03

Brand: Panasonic Pages: 66

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Safeline Pages: 44

Brand: Unify Pages: 218

Brand: Viking Pages: 2

Brand: Telstra Pages: 6

Brand: BT Pages: 70

Enterprise Edge CAPN

Brand: Nortel Pages: 7

Brand: Uniden Pages: 32

Brand: Auerswald Pages: 16

Brand: GAI-Tronics Pages: 20

Brand: BellSouth Pages: 33

Brand: Neon Pages: 44

Brand: Flying Voice Pages: 64

Brand: switel Pages: 144

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands