Sonifex DHY-03 User Handbook Manual Download Page 49

Page: 49 / 56

DHY-03 User Handbook

Line

Output

Mic/Line

Input

Conference

Audio

Telephone

Handset

Telephone

Line

Fuse

Holder

Mains

Input

Remotes

RS232 Serial

Port

Protective

Earth Terminal

Pin2

Phase Signal
Pin 1

Screen Signal
Pin 3

Non-phase Signal

Pin2

Phase Signal
Pin 1

Screen Signal
Pin 3

Non-phase Signal

4 Technical Specification

DHY-03 Connection Details

All of the connections are located on the rear of the DHY-03 :

Figure 4-1 : DHY-03 Rear Panel Connections.

Line Output

The line output is an XLR 3 pin male connector (XLR-3-32, 50 Ω balanced floating).

Pin 1     :  Screen
Pin 2     :  Phase
Pin 3     :  Non-phase

Mic/Line Input

The line input is an XLR 3 pin female connector (XLR-3-31, 10k Ω balanced floating).

Pin 1     :  Screen
Pin 2     :  Phase
Pin 3     :  Non-phase

TECHNIC

AL SPECIFIC

TION

TECHNICAL SPECIFICATION

Summary of Contents for DHY-03

























































Search results

Summary of Contents for DHY-03

Reviews:

Brands by name

Popular brands

Sonifex DHY-03, User Handbook Manual

Search results

Summary of Contents for DHY-03

Reviews:

Brands by name

Popular brands