Sonifex DHY-03 User Handbook Manual Download | Manualshive

Page: 29 / 56

background image

DHY-03 User Handbook

15

Configuration & Controls - DHY-03EC

Controls

C

ONFIGUR

A

TION & C

ONTR

OLS

CONFIGURATION & CONTROLS

2

Rx Level LED

Figure 2-6 : DHY-03EC Controls.

Power LED Indicator

The power LED indicates that the equipment is powered and operational when illuminated.

Gain Jumpers

Refer to Fig 2-8. These jumpers allow gain/attenuation to be applied to the incoming &
outgoing analogue audio. Each jumper has 3 positions, jumper 1-2, off and 3 jumper 2-3
that give gains of -6dB, 0dB & +6dB respectively. The normal position for the transmit gain
to the telephone line (J3 off) is 0db and for the receive gain from telephone line (J4 1-2)
is –6dB.

Tricolour LED Level Indicators

These Tricolour LEDs indicate the signal level of the incoming audio signal (left) and level
received from line (right). For best operation set the signal gain switches to achieve LED
mostly illuminated yellow with occasional audio peaks lighting the red LED.

The scale indicates – Green (-30dB, to -3dB); Yellow (-3dB, to +6dB); & Red (+6dB, LED).

Tx Level LED

Settings Dip Switch

Reset Button

Power On LED

«
...
27
28
29
30
31
...
»

Summary of Contents for DHY-03

























































Reviews:

No comments

Related manuals for DHY-03

Brand: UniData Communication Systems Pages: 8

WPU-7700 Enterprise Edition

Brand: UniData Communication Systems Pages: 41

Venture IP 480i

Brand: Aastra Pages: 12

BUTLER 2551 Deluxe

Brand: Topcom Pages: 52

Brand: Uniden Pages: 36

Brand: Telstra Pages: 40

Brand: Bittel Pages: 6

CLEAR TRIM-FONE 43-858

Brand: Radio Shack Pages: 2

Brand: QBest Pages: 17

Brand: Panasonic Pages: 69

Brand: Philips Pages: 29

TRIPLEX SDJ6051

Brand: Philips Pages: 2

Wall Jack SDJ6000W

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 1

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands