Sonifex DHY-03 User Handbook Manual Download | Manualshive

Page: 10 / 56

background image

iv

DHY-03 User Handbook

Safety Information

Safety of Mains Operated Equipment

This equipment has been designed to meet the safety regulations currently advised
in the country of purchase and it conforms to the safety regulations specified by
use of the CE Mark.

Warning : There are no user serviceable parts inside the equipment. If you should ever
need to look inside the unit, always disconnect the mains supply before removing the
equipment covers.

Warning: The DHY-03 line socket should only be connected with apparatus
complying with BS6301, and the connection to the network must not be hard wired
Interconnection directly or indirectly with equipment ports marked in accordance with
BS6301 to unmarked ports may produce hazardous conditions on the network and
advice should be obtained from a competent engineer before such a connection is made.

Warning: This apparatus must be earthed by means of the earth connector on the rear
panel, and the connection to the telecommunications network should be removed
before disconnecting the earth. Disconnection of this earth connection may render the
equipment unsafe, with a consequential possible electrical shock hazard from exposed
metallic parts.

Warning: The barriered ports ‘LINE’ and ‘HANDSET’ must not be connected directly
or indirectly to the un-barriered ports, ‘MIC/LINE INPUT’, ‘OUTPUT’, ‘CONFERENCING’,
‘REMOTES’ or ‘RS-232’.

Voltage Setting Checks

The integral power supply is designed to accept a universal input of 85 to 264 VAC mains
input voltage. The safety specification of your DHY-03 complies with local requirements and
must be earthed through the mains connector.

Fuse Rating

The DHY-03 is supplied with a single fuse in the live conducting path of the mains power
input. For reasons of safety it is important that the correct rating and type of fuse is
used. Incorrectly rated fuses could present a possible fire hazard, under equipment fault
conditions. The fuse rating for DHY-03 is:

230 or 115 V operation - 1A 5 x 20mm SB

The active fuse is fitted on the outside rear panel of the unit.

SAFE

T

Y INFORM

A

TION

SAFETY INFORMATION

«
...
8
9
10
11
12
...
»

Summary of Contents for DHY-03

























































Reviews:

No comments

Related manuals for DHY-03

Brand: 3Com Pages: 84

SuperStack 3 NBX

Brand: 3Com Pages: 496

Brand: 3CX Pages: 15

Brand: CEECO Pages: 11

PhoneEasy 331ph

Brand: Doro Pages: 2

Brand: Topcom Pages: 28

Brand: Binatone Pages: 32

Brand: BT Pages: 67

Brand: Geemarc Pages: 2

AmpliDECT 595 Photo

Brand: Geemarc Pages: 52

Brand: Kraun Pages: 2

2420 - VT Cordless Extension Handset

Brand: Gigaphone Pages: 38

Gigaset M2 Ex professional

Brand: Unify Pages: 61

OpenScape CP200

Brand: Unify Pages: 321

Brand: Medion Pages: 256

Brand: JOIWO Pages: 32

Definity Callmaster IV

Brand: Avaya Pages: 26

Brand: Fanvil Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands