manualshive.com logo in svg

Sonifex DHY-03, User Handbook Manual

Share
Download
Sonifex DHY-03 User Handbook Manual Download Page 30

16

DHY-03 User Handbook

Status & Operating Mode Information

The Tricolour LEDs are also used to indicate special operating modes and other settings  
as follows:

.

 

Alternating Rx, Tx Yellow pattern indicates that the DHY-03 is checking the status of 
the Line Connect Button to test the Bootstrap Mode (see page 24).

.

 

Alternating Rx, Tx Yellow/Rx, Tx off pattern indicates that the DHY-03 has entered 
Bootstrap mode, because either the Line Connect Button was held down for ~10 
seconds at power up, or the Main code has been corrupted (most likely due to a 
previous incomplete firmware update).

.

 

Alternating Rx Red, Tx Green/Rx Green, Tx Red pattern indicates that the DHY-03 has 
received a ‘DWN’ command from the serial port and is updating the firmware (valid in 
either Bootstrap or Normal operation).

.

 

On normal power up the top row of LEDs shows the current country selection. Count 
the Tx & Rx flashes and the country code is the sum of Tx multiplied by 16, plus Rx  
(see Table 2-1) 

.

 

If there is a fault during power up, the Tx Red & Rx Red LEDs will flash alternately.

.

 

Once initialisation is complete the LEDs show the level info as above.

Reset Button

In the unlikely event that the DHY-03 unit fails to respond, press the reset button to reboot 
the unit.

Configuration Settings Switches

The SETTINGS switches are used to configure the DHY-03 in the modes that you want  
it to operate. A label on the top panel of the unit shows the orientation of the switches:  
The following paragraphs describe the function of each switch; the default or normal 
position is shown in curly brackets.

Figure 2-7 : DHY-03EC Configuration Settings Switches.

C

ONFIGUR

A

TION & C

ONTR

OLS

CONFIGURATION & CONTROLS

2

Coun

tr

y S

et 

 

on P

ow

er Up

Noise G

at

e  

Selec

t

Ac

oustic 

 

Canc

ella

tion 

 

Enable

1 2 3 4 5 6 7 8 9 10

ON

Net

w

or

k  

Canc

ella

tion 

 

Enable

Aut

o A

nsw

er 

 

Enable

Aut

o  

Disc

onnec

t  

Enable

D

uck

ing Enable

Unused

M

omen

tar

y La

tch 

Func

tion O

f R

emot

e 

Line Hold

U

ser S

elec

table 

D

ebug

Summary of Contents for DHY-03

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands