Sonifex DHY-03 User Handbook Manual Download Page 53

Page: 53 / 56

DHY-03 User Handbook

Technical Specification

Feature

Value

Input Impedance – Line Mode (Clean
Feed)

>10kΩ balanced 0dB, optimum working input
level 0 to+8dBu

Input Impedance – Microphone Mode

200Ω balanced

Clean Feed Limiting Input

+4dBu

Microphone Level Range

-70dB to –52dB adjusted by preset pot & ±6dB
from gain switch

Bandwidth to Telephone Line

125Hz – 3.6kHz, -3dB ref 1kHz

Telephone Line Impedance

Nominally 600Ω - complex impedances set via
country code

Telephone Line Impedance Range

300Ω to 1500Ω

Output Impedance

50Ω balanced floating 0dBu

Output Level Range

±6dB from receive gain switch

Rejection Ratio

78dB on 1kHz tone, typically 75dB on complex
waveforms, reference peak level of 0dB

Ring Detector Sensitivity

1 ring to 10 rings

Power

Filtered IEC, continuously rated 85-264V AC @
47-63Hz,max 10W

Power to DHY-03EC

±15 V DC @ 160mA per rail
or reg5 V DC @ 600mA

Table 4-1 : Technical Specification.

Physical Specification

Order
Code

Description

Height

Width

Depth

Total Nett

Weight

Total Gross

Weight

DHY-03

Automatic digital TBU
with ringing detector,
free standing

4.5cm

21.8cm 17.5cm*

1.25kg

2.0kg

DHY-03S

Automatic digital TBU
with ringing detector,
19” rack mounted

4.5cm

(1U)

48.3cm

(19” rack

width)

17.5cm*

1.30kg

2.1kg

DHY-03T

Twin automatic
digital TBU with
ringing detector, 19”
rack mounted

4.5cm

(1U)

48.3cm

(19” rack

width)

17.5cm*

2.60kg

4.0kg

DHY-03EC

Automatic digital TBU
with ringing detector
Eurocard model
(PCB 10x16cm)

12.9cm

(3U)

4.0cm

(8E)

19.0cm

150g

500g

Table 4-2 : Physical Specification.

*Depth is measured from the front of the divert button to the back of the remotes connectors.

TECHNICAL SPECIFICATION

TECHNIC

AL SPECIFIC

TION

Summary of Contents for DHY-03

























































Search results

Summary of Contents for DHY-03

Reviews:

Brands by name

Popular brands

Sonifex DHY-03, User Handbook Manual

Search results

Summary of Contents for DHY-03

Reviews:

Brands by name

Popular brands