Sonifex DHY-03 User Handbook Manual Download | Manualshive

Page: 48 / 56

background image

34

DHY-03 User Handbook

Disconnect Tones – parameters 200,208,216,224,232,240

This value is an indication of the disconnect tone parameters – the tone frequencies and
cadence are only set by changing the parameters below.

Tone Frequency

Value

Type of Tone

Value

350Hz

1

Cadence

16384

400Hz

2

Continuous

32768

425Hz

4

440Hz

8

450Hz

16

480Hz

32

620Hz

64

900Hz

128

User Frequency

8192

Table 3-18 : Table of Disconnect Tone Values.

(Use sum of required values)

Cadence Pattern 1 – parameters 201,209,217,225,233,241

This parameter is set to define a cadence pattern (set to 0 if none). The On time is set in 8ms
steps (i.e. 80ms on time is 10steps) this value is multiplied by 256 and added to the off time.
The off time is also in set in 8ms steps so a cadence pattern of 80ms on and 120ms off is
15 = 2575.

Success Time/Cadence Pattern 2 – parameters 202,210,218,226,234,242

If cadence pattern 1 is zero (i.e. cadence patterns are not set) then this parameter
determines the no of successive tone tests that need to detect the tone before
disconnecting the call. Multiply this value by the number of cycles and divide by 8 for the
time in milliseconds for which the tone must be present before disconnecting.

When cadence pattern is non-zero then this parameter is set in the same way as cadence
pattern 1 above. It is only used when there is a double pattern in the signal cadence.

Cycles for Transform – parameters 203,211,219,227,235,243

Together with the coefficients below this parameter is the number of cycles required by the
DSP to detect the tone(s) accurately. The number is dependant on the tone or combinations
of tones used.

Coefficient for Tone 1 – parameters 204,212,220,228,236,244

This parameter sets the coefficient for the tone detection algorithm.

Coefficient for Tone 2 – parameters 205,213,221,229,237,245

This parameter sets the coefficient for the second tone detection algorithm; if only single
tone detection is required then this parameter should be set to zero.

Threshold Level – parameters 206,214,222,230,238,246

This parameter sets the acceptable level that a tone must be present for successful
detection of that tone to be indicated.

SERIAL PORT CONTROL

SERIAL PORT C

ONTR

OL

3

«
...
46
47
48
49
50
...
»

Summary of Contents for DHY-03

























































Reviews:

No comments

Related manuals for DHY-03

Brand: IBM Pages: 84

Business Analog Telephone

Brand: Tekelec Pages: 145

Brand: BT Pages: 80

Brand: Uniden Pages: 33

Brand: Motorola Pages: 200

Brand: Motorola Pages: 8

Brand: HAGENUK Pages: 52

Gigaset M2 Ex professional

Brand: Unify Pages: 61

OpenScape CP200

Brand: Unify Pages: 321

Brand: Wildix Pages: 2

Brand: Sprint Pages: 32

Brand: Conairphone Pages: 3

Brand: Conairphone Pages: 7

Brand: AGFEO Pages: 8

Brand: Fonexion Pages: 56

Brand: voptech Pages: 93

allrounder A694

Brand: Gigaset Pages: 59

Brand: Polaris Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands