Sonifex DHY-03 User Handbook Manual Download | Manualshive

Page: 38 / 56

background image

24

DHY-03 User Handbook

3 Serial Port Control

DHY-03 Serial Connection

Default connection is 19200, e, 8, 1 and using XON/XOFF handshaking. There are 3 modes of
operation for the serial port –

Normal Mode

allows the user to monitor & control the DHY-03.

Setting Mode

allows the user to change the operating parameters; generate a default set

of cancellation coefficients; search for the best line impedance matching characteristic: and
update the firmware of the DHY-03 hybrid. In setting mode no call control is available.

Bootstrap Mode

is entered by default when the flash memory doesn’t contain valid

firmware (e.g. when a firmware update has been interrupted) or can be forced by powering
up the DHY-03 whilst holding the front panel Line Connect Button on for 10 seconds.

SCI Software

Sonifex provide free of charge software, SCI, to allow the user to manage connection and
control of all aspects of the serial port interface: - go to www.sonifex.co.uk/sci for the
latest version.

The telephone interface parameters are accessible from the serial port for changing the
settings for use on non-standard telephone systems or PABXs and would not normally need
to be changed on standard systems. Many of these parameters are critical to the correct
operation of the DHY-03. Changing them may impact on the correct working of the unit
or cause the unit to operate in a way that is outside the telecom approval regimes. Our
advice is that the telephone interface parameters should not be changed without detailed
technical knowledge or input from Sonifex. Both country code and disconnect type tables
have reserved entries for future additions, if you have special requirements for either of
these parameters please contact us with details and we can assess the demand and then
add to the standard list as required.

Serial Interface Commands & Responses

Normal Mode Commands

ANS:

- Answer Call

- ACK: or NAK:

Bnn:

- Baud Rate

- ACK: or NAK: (at old rate)

nn=11 (115200)

nn=57 (57600)

nn=38 (38400)

nn=19 (19200)

nn=96 (9600)

BSV:

- BootStrap version

- BOOT:x.xx

CLR:

- Clear Call

- ACK: or NAK:

RST:

- Reset Serial Port

- _OK_

SER:

- Serial Num request

- SER:xxxxx

SET:

- Enter Settings Mode

- ACK: or NAK:

SRQ:

- Status Request

- SRQ:nn where nn is state of DHY-03

SERIAL PORT CONTROL

SERIAL PORT C

ONTR

OL

3

«
...
36
37
38
39
40
...
»

Summary of Contents for DHY-03

























































Reviews:

No comments

Related manuals for DHY-03

Brand: Octopus Pages: 131

Brand: Panasonic Pages: 24

Brand: Talkswitch Pages: 334

Brand: M-Life Pages: 16

Brand: Orchid Telecom Pages: 25

Brand: Ameriphone Pages: 27

Brand: Gigaset Pages: 49

Clarity Extra W1100

Brand: Walker Pages: 27

Brand: Aastra Pages: 100

Brand: Talkaphone Pages: 6

Brand: Binatone Pages: 32

DCT70585 Series

Brand: Uniden Pages: 76

Brand: CHARITY MOBILE Pages: 14

Brand: SAN/BAR Pages: 11

Brand: GE Pages: 56

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands