manualshive.com logo in svg

Soneco CC3, User Manual

Share
Download
Soneco CC3 User Manual Download Page 7

 

 

   

  

™

 

 

7(20) 

 

 

 

© Soneco Oy.

  

 

V 23.7.2013 

 

Staus: Contents schecked 

Author: JR 

4. The programming mode 

The  settings  for  the  CC3  are  programmed  with  text  messages  in  the programming 
mode. This mode is indicated by alternating blinks of GREEN and YELLOW lights. 

There are a few different ways to get the device to the programming mode. Which of 
these  are  to  be  used  depends  on  the  settings  of  the  device.  The  available 
possibilities are explained below in chapters 4A – 4C. 

4A. DEVICE WITH DEFAULT SETTINGS 
Wait  during  start-up  until  the  GREEN  light  is  on  for  5  seconds.  Press  the  button 
once during this period. The device enters the programming mode.  

4B. A DEVICE WITH POWER-OFF PREVENTION 
A  device  with  inhibited  power-OFF  can  be  commanded  to  the  programming  mode 
with a PRG-command from a number stored in the device (see 4C) or by switching it 
OFF  via  LIMITED  mode  and  then  restarting  the  device.  If  the  device  is  in  standby 
mode, it enters the LIMITED mode after removing the SIM as in Fig. 1. Remove the 
SIM  and  wait  until  the  device  indicates  a  SIM-error.  Return  the  SIM  to  the  device. 
Wait  during  the  start-up  until  the  GREEN  light  goes  on  for  5  seconds.  Press  the 
button  once  during  this  period.  The  device  enters  the  programming  mode.  Note:  If 
you  miss  the  time  window  during  the  automatic  re-start  you  can  also  switch  the 
device OFF in LIMTED mode and start it normally. 

4C DEVICE WITH INHIBITED MANUAL ENTRY TO PROGRAMMING MODE  
Programming mode is possible only if the device receives a command <<<PRG>>> 
as a text message from a number that is stored in the device. 

EXECUTION OF A PROGRAMMING COMMAND 
If a programming command is accepted and executed, the device gives an audible 
signal  and  the  YELLOW  light  blinks  once  notably  longer.  The  programming  mode 
continues.  

If a programming command is rejected, the device gives three audible signals and 
the RED light blinks. The programming mode continues. A rejected command is not 
executed in full, i.e. part of it may have been executed.  

VERIFICATION AND TERMINATION OF PROGRAMMING 

Pressing  the  button  longer  than  5  seconds  causes  the  device  to  send  the  stored 
settings as a text message to the first number if it is given.   

Programming mode is terminated with a short press of the button. The device shuts 
off. 

 

5. The purpose and setting of the telephone numbers 

Number1, Number2 and  Number3:  After  a single  press  of  the button, CC3 tries to 
make  a  voice  call  to  these  numbers.  The  length  and  the  number  of  attempts  to 
make the voice call can be defined with the parameters of the calling engine. 

X-number  and  U-number:  CC3  has  option  to  set  a  4

th

  X-number  and  a  5

th

  U-

number.  The  X-umber  (e

X

tra  number)  can  be  used  as  an  emergency  number  for 

situations when the numbers 1 to 3 can not be reached. In CC3, the X number is for 
voice  calls.  The  U-number  (

U

nlocking  number)  is  only  for  the  management 

Summary of Contents for CC3





















Reviews:

No comments

Brands by name

Popular brands

Load more brands