manualshive.com logo in svg

Soneco CC3, User Manual

Share
Download
Soneco CC3 User Manual Download Page 3

 

 

   

  

™

 

 

3(20) 

 

 

 

© Soneco Oy.

  

 

V 23.7.2013 

 

Staus: Contents schecked 

Author: JR 

List of contents

Warranty..................................................................................................................2

 

Purpose of CC3.......................................................................................................4

 

To start with.............................................................................................................4

 

Preparing for the use...............................................................................................4

 

Quick procedure for using MC3 for the first time .....................................................5

 

1. Charging of the battery........................................................................................6

 

2.  Warning message due to low battery .................................................................6

 

3. Start-up ...............................................................................................................6

 

4. The programming mode ......................................................................................7

 

5. The purpose and setting of the telephone numbers............................................7

 

6. Setting the alarm message..................................................................................8

 

7. Basic settings ......................................................................................................9

 

8. Options ................................................................................................................9

 

8.1. Options for power ON and OFF.................................................................... 9

 

8.2. Options for voice calls ................................................................................ 10

 

8.3. Security and general settings ..................................................................... 11

 

9. Standby mode ...................................................................................................12

 

10. Making a call, sending a message, receiving a call and responding to a calling 
effort ......................................................................................................................12

 

10.1. Starting of the calls and sending of the messages ................................... 12

 

10.2. Receiving and terminating of the calls...................................................... 13

 

10.3. Receiving and terminating of the calling efforts........................................ 13

 

10.4. Adjusting the features of the voice call ..................................................... 13

 

11. Special features during alarm mode................................................................13

 

12. Shutting the device off.....................................................................................14

 

13. Request for battery charge status ...................................................................14

 

14. Voice call features in alarm state ....................................................................14

 

15. Emergency call 112.........................................................................................14

 

16. Remote controlled voice call "CALL" and termination of a call "END CALL" and 
queuing of a call ....................................................................................................15

 

17. The life-time, capacity and maintenance of the battery...................................15

 

18. The use in challenging environments ..............................................................15

 

19. Data security, privacy, reliability and prevention of abuse...............................16

 

20. Unrecognized fault situations ..........................................................................16

 

Annex A: Tone and light indications of CC3..........................................................18

 

Important to observe .............................................................................................20

 

Technical specifications: .......................................................................................20

 

Declaration of conformity:......................................................................................20

 

 

Summary of Contents for CC3





















Reviews:

No comments

Brands by name

Popular brands

Load more brands